FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. CheckPoint Certification
  3. 156-836 Exam
  4. CheckPoint.156-836.v2024-09-01.q28 Dumps
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • »
Download Now

Question 1

Is it possible to define distribution mode per interface?

Correct Answer: D
Explanation
Maestro allows you to define the distribution mode per interface, which determines how traffic is distributed among the Security Group Modules (SGMs) in a Security Group. You can configure the distribution mode for each interface individually, or use the default mode for all interfaces. The distribution mode can be set for both uplink and downlink interfaces.
References =
*Check Point Maestro R81.X Administration Guide, page 62, section "Distribution Mode" 1
*Check Point Maestro R81.X Getting Started Guide, page 25, section "Distribution Mode" 2
1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2:
https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frame
insert code

Question 2

During an upgrade, Is Multi-Version Clustering (MVC) supported?

Correct Answer: D
Explanation
Multi-Version Clustering (MVC) is a feature that allows different versions of Security Gateways to operate in the same cluster and provide seamless failover and load balancing. MVC is supported for Maestro environments as of R81, which means that it is possible to upgrade the Security Groups in a Maestro environment as a Multi-Version Cluster with zero downtime. This requires that the Maestro Orchestrators are upgraded to R81.20 first, and then the Security Groups can be upgraded one by one to R81.20 while maintaining full connectivity and synchronization.
References =
*Check Point R81.20 for Scalable Platforms - Check Point Software
*Maestro Dual Site configuration with a direct connection through L2 switches
*CHECK POINT MAESTRO EXPERT
insert code

Question 3

What is the max amount of Orchestrators in Dual-site setup?

Correct Answer: B
Explanation
A Dual Site setup can have either two or four orchestrators, depending on the scenario. However, the maximum number of orchestrators per Security Group is four, regardless of the number of sites. This is because each Security Group can have up to two orchestrators on each site, and each site can have up to two orchestrators. Therefore, the maximum number of orchestrators in a Dual Site setup is four per Security Group.
References =
*Maestro Frequently Asked Questions (FAQ)
*Maestro Dual Site configuration with a direct connection through L2 switches
*Dual Site Single Maestro Hyperscale Orchestrator Cluster (Dual Site Single MHO Redundancy)
insert code

Question 4

There is a Security group of 10 Appliances and all of them are up and running. How many Appliances within a Security Group keep the same connection in its connection table in case of NAT?

Correct Answer: A
Explanation
References =
*Check Point Maestro R81.X Administration Guide, page 64, section "Correction Layer" 1
*Check Point Maestro R81.X Getting Started Guide, page 26, section "Correction Layer" 2
*Check Point Maestro Under the Hood presentation by Lari Luoma, slide 23
*Check Point Maestro Frequently Asked Questions (FAQ), question 9
1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2:
https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frame
:
https://community.checkpoint.com/fyrhh23835/attachments/fyrhh23835/maestro/1191/1/Check%20Mates%20M
:
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=
insert code

Question 5

There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks' intra- orchestrator redundancy when using two Orchestrators?

Correct Answer: D
Explanation
This configuration likely provides balanced and redundant connectivity for orchestrator redundancy.
References
*Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 3: Dual Orchestrator Environment, Lesson 3.1: Introduction to Dual Orchestrator Environment, page 3-7
*Check Point R81 Maestro Administration Guide, Chapter 3: Working with Security Group Modules, Section:
Downlinks, page 3-8
*Check Point 23800 Appliance Datasheet - Check Point Software, page 2
insert code
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • »
[×]

Download PDF File

Enter your email address to download CheckPoint.156-836.v2024-09-01.q28 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2025 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.