FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. CheckPoint Certification
  3. 156-836 Exam
  4. CheckPoint.156-836.v2025-12-29.q54 Dumps
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
Download Now

Question 1

What is the max amount of Orchestrators in Dual-site setup?

Correct Answer: B
Explanation
A Dual Site setup can have either two or four orchestrators, depending on the scenario. However, the maximum number of orchestrators per Security Group is four, regardless of the number of sites. This is because each Security Group can have up to two orchestrators on each site, and each site can have up to two orchestrators. Therefore, the maximum number of orchestrators in a Dual Site setup is four per Security Group.
References =
*Maestro Frequently Asked Questions (FAQ)
*Maestro Dual Site configuration with a direct connection through L2 switches
*Dual Site Single Maestro Hyperscale Orchestrator Cluster (Dual Site Single MHO Redundancy)
insert code

Question 2

What type of license is required for an MHO?

Correct Answer: C
Explanation
The MHO (Maestro Hyperscale Orchestrator) does not require a license by itself, but each SGM (Security Group Module) that is attached to the MHO needs a license. The license type depends on the features and blades that are enabled on the SGM. For example, if the SGM is running VSX, it needs a VSX license.
References:
*Maestro Expert (CCME) Course - Check Point Software, page 71
*Check Point Certified Maestro Expert (CCME) R81.X - Global Knowledge, course outline
insert code

Question 3

For the MHO-175, which ports are Management ports?

Correct Answer: B
Explanation
According to the Port Mapping for the Check Point Maestro HyperScale Orchestrator MHO-175 document1, ports 1 - 4 are Management ports that are used to connect the MHO to the customer's management infrastructure, such as SmartConsole or SmartDomain Manager. Ports 5 - 26 are Uplink ports that are used to connect the MHO to the customer's network infrastructure, such as switches, routers, or firewalls. Ports 27 -
47 are Downlink ports that are used to connect the MHO to the Security Group Modules (SGMs) in the Security Group. Ports 49 - 55 are Backplane ports that are used to connect the MHO to another MHO in a Dual Orchestrator environment.
References:
*Maestro Expert (CCME) Course - Check Point Software, page 42
*Check Point Certified Maestro Expert (CCME) R81.X - Global Knowledge, course outline3
*Port Mapping for the Check Point Maestro HyperScale Orchestrator MHO-1751
insert code

Question 4

While looking at your system's correction statistics, you notice you have a correction rate approaching 100 percent. Is this a problem?

Correct Answer: B
Explanation
References =
*Check Point Maestro R81.X Administration Guide, page 64, section "Correction Layer" 1
*Check Point Maestro R81.X Getting Started Guide, page 26, section "Correction Layer" 2
*Check Point Maestro Under the Hood presentation by Lari Luoma, slide 23 3
*Check Point Maestro Frequently Asked Questions (FAQ), question 9 4
1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2:
https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frame
3:
https://community.checkpoint.com/fyrhh23835/attachments/fyrhh23835/maestro/1191/1/Check%20Mates%20M
4:
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=
insert code

Question 5

What is the purpose of RJ-45 connectors located at the front panel of the Orchestrator MHO-170?

Correct Answer: C
Explanation
The RJ-45 connectors located at the front panel of the Orchestrator MHO-170 are used for out-of-band management and serial console access. One of them is a 1Gbps RJ-45 port that provides an out-of-band interface for accessing the Orchestrator itself for configuration and management purposes. The other one is a RJ-45 serial console port that provides a command-line interface for initial setup and troubleshooting.
References
*Maestro Hyperscale Orchestrator Datasheet - Check Point Software1, page 2
*Quantum Maestro Getting Started Guide - Check Point CheckMates, page 4
insert code
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download CheckPoint.156-836.v2025-12-29.q54 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2025 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.