Refer to the exhibit.

The forwarding entries how that the next hop for prefixes from the 172.16.0.0/16 network is set to 10.2.2.2 instead of 10.1.1.1. Which action resolves the issue?

• A.Remove the continue 20 statement from route-map RED permit 10
• B.Add the continue statement in route-map RED permit 10 instead of continue 20.
• C.Add set ip next hop 10.1.1.1 in route-map RED permit 20.
• D.Remove match ip address prefix-list 1 from route-map RED permit 10.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

An engineer must configure EIGRP between R1 and R2 with no summary route. Which configuration resolves the issue?

• A.
• B.
• C.
• D.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

Refer to the exhibit. An engineer examines the BGP update for the IPv6 prefix 2001:db8::1/128. which should have been summarized into a /64 prefix. Which sequence of actions achieves the summarization?

• A.R1 is a route reflector with a router ID of 3.3.3.3. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
• B.R1 is a route reflector with a router ID of 1.111. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
• C.R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to different ASs. The prefix is not advertised to any peer and must be advertised using the network statement on R3.
• D.R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to the same AS. Configure an aggregate address on the router with ID 3 3.3.3 for the prefix.

Comment: *

Name: *

Email: *

Verification: *

Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

Correct Answer:

Explanation
Same Answer is already updated below:

HTTP and HTTPs run on TCP port 80 and 443, respectively and we have to remember them.
Syslog runs on UDP port 514 while NTP runs on UDP port 123 so if we remember them we can find out the matching answers easily. But maybe there is some typos in this question as 2001:d88:800:200c::c/126 only ranges from 2001:d88:800:200c:0:0:0:c (4 hosts in total). It does not cover host 2001:0D88:0800:200c::1f. Same for , which also ranges from
2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f and does not cover host 2001:0D88:0800:200c::1c
.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

In which circumstance does the BGP neighbor remain in the idle condition?

• A.if prefixes are not received from the BGP peer
• B.if prefixes reach the maximum limit
• C.if a prefix list is applied on the inbound direction
• D.if prefixes exceed the maximum limit

Comment: *

Name: *

Email: *

Verification: *