Refer to the exhibits.

While troubleshooting, a network engineer discovers that the backup path fails between ASBR3 and ASBR4 for traffic between BGP AS6000 and BGP AS6500 when the connection between ASBR1 and ASBR2 goes down. The following configurations were performed on ASBR1:

Which command is missing?

• A.bgp additional-paths Install
• B.bgp additional-paths select
• C.redistribute static
• D.bgp advertise-best-external

Comment: *

Name: *

Email: *

Verification: *

An engineer must edit the settings of a site-to-site IPsec VPN connection between an on-premises Cisco IOS XE router and Amazon Web Services (AWS). IPsec must be configured to support multiple peers and failover after 120 seconds of idle time on the first entry of the crypto map named Cisco. Drag and drop the commands from the left onto the order on the right.

Correct Answer:

Explanation:
Step 1 = crypto map cisco 1 ipsec-isakmp Step 2 = set peer 192.168.10.1 default Step 3 = set peer
192.168.20.1 Step 4 = set security-association idle-time 120 default
The process of editing the settings of a site-to-site IPsec VPN connection between an on-premises Cisco IOS XE router and Amazon Web Services (AWS), and configuring IPsec to support multiple peers and failover after 120 seconds of idle time on the first entry of the crypto map named Cisco involves several steps123456.
crypto map cisco 1 ipsec-isakmp: This command is used to create a new entry in the crypto map named
"cisco". The "1" is the sequence number of the entry, and "ipsec-isakmp" specifies that the IPSec security associations (SAs) should be established using the Internet Key Exchange (IKE) protocol13.
set peer 192.168.10.1 default: This command is used to specify the IP address of the default peer for the crypto map entry. In this case, the default peer is at IP address 192.168.10.115.
set peer 192.168.20.1: This command is used to add an additional peer to the crypto map entry. In this case, the additional peer is at IP address 192.168.20.1. This allows the IPsec VPN to support multiple peers56.
set security-association idle-time 120 default: This command is used to set the idle time for the security association. If no traffic is detected over the VPN for the specified idle time (in this case, 120 seconds), the security association is deleted, and the VPN connection fails over to the next peer46.
References :=
Configure a Site-to-Site IPSec IKEv1 Tunnel Between an ASA and a Cisco IOS Router - Cisco Configure IOS-XE Site-to-Site VPN Connection to Amazon Web Services - Cisco Community Configuring Site to Site IPSec VPN Tunnel Between Cisco Routers Configure Failover for IPSec Site-to-Site Tunnels with Backup ISP Links on FTD Managed by FMC - Cisco Does Setting Multiple Peers in a Crypto Map Also Support Parallel IPSec Connections - Cisco Community Multiple WAN Connections - IPsec in Multi-WAN Environments | pfSense Documentation Multiple Set Peer for VPN Failover - Server Fault

Comment: *

Name: *

Email: *

Verification: *

An engineer must use Cisco vManage to configure an application-aware routing policy Drag and drop the steps from the left onto the order on the right to complete the configuration.

Correct Answer:

Explanation:
Step 1 = Create the groups of interest. Step 2 = Configure the topology. Step 3 = Create the application-aware routing policy. Step 4 = Apply the application-aware routing policy to a specific VPN and sites.
The process of configuring an application-aware routing policy in Cisco vManage involves several steps12.
Create the groups of interest: This is the first step where you define the applications or groups that the policy will affect1.
Configure the topology: This involves setting up the network topology that the policy will operate within1.
Create the application-aware routing policy: After setting up the groups and topology, you then create the application-aware routing policy. This policy tracks network and path characteristics of the data plane tunnels between Cisco SD-WAN devices and uses the collected information to compute optimal paths for data traffic31.
Apply the application-aware routing policy to a specific VPN and sites: Finally, the created policy is applied to a specific VPN and sites. This allows the policy to affect the desired network traffic1.
References :=
Designing and Implementing Cloud Connectivity (ENCC) v1.0
Learning Plan: Designing and Implementing Cloud Connectivity v1.0 (ENCC 300-440) Information About Application-Aware Routing - Cisco Configuring Application-Aware Routing (AAR) Policies | NetworkAcademy.io Policies Configuration Guide, Cisco IOS XE SD-WAN Releases 16.11, 16.12

Comment: *

Name: *

Email: *

Verification: *

A company with multiple branch offices wants a connectivity model to meet its network architecture requirements. The company focuses on ensuring low latency and efficient routing for its critical business applications. Which connectivity model meets these requirements?

• A.hub-and-spoke topology with SD-WAN technology, using dynamic routing and OSPF as the routing protocol
• B.fully meshed topology with SD-WAN technology, using dynamic routing and BGP as the routing protocol
• C.point-to-point topology using dedicated leased lines and static routing
• D.star topology with internet-based VPN connections and static routing

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

A network engineer discovers that the policy that is configured on an on-premises Cisco WAN edge router affects only the route tables of the specific devices that are listed in the site list. What is the problem?

• A.An inbound policy must be applied.
• B.The action must be set to deny
• C.A localized data policy must be configured.
• D.A centralized data policy must be configured

Comment: *

Name: *

Email: *

Verification: *