FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. Cisco Certification
  3. 350-401 Exam
  4. Cisco.350-401.v2022-12-29.q599 Dumps
  • ««
  • «
  • …
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • …
  • »
  • »»
Download Now

Question 276

Which action is a function of VTEP in VXLAN?

Correct Answer: C
Explanation
VTEPs connect between Overlay and Underlay network and they are responsible for encapsulating frame into VXLAN packets to send across IP network (Underlay) then decapsulating when the packets leaves the VXLAN tunnel.
VTEPs connect between Overlay and Underlay network and they are responsible for encapsulating frame into VXLAN packets to send across IP network (Underlay) then decapsulating when the packets leaves the VXLAN tunnel.
insert code

Question 277

Refer to the exhibit.

An engineer must permit traffic from these networks and block all other traffic An informational log message should be triggered when traffic enters from these prefixes Which access list must be used?

Correct Answer: D
insert code

Question 278


Refer to the exhibit. An engineer must deny HTTP traffic from host A to host V while allowing all other communication between the hosts, drag and drop the commands into the configuration to achieve these results.
Some commands may be used more than once. Not all commands are used.

Correct Answer:

Explanation
Deny
Permit
Action drop
Action forward
insert code

Question 279

An engineer is concerned with the deployment of a new application that is sensitive to inter-packet delay variance. Which command configures the router to be the destination of jitter measurements?

Correct Answer: D
insert code

Question 280

Which configuration restricts the amount of SSH that a router accepts 100 kbps?
A)

B)

C)

D)

Correct Answer: C
Explanation
CoPP protects the route processor on network devices by treating route processor resources as a separate entity with its own ingress interface (and in some implementations, egress also). CoPP is used to police traffic that is destined to the route processor of the router such as:
+ routing protocols like OSPF, EIGRP, or BGP.
+ Gateway redundancy protocols like HSRP, VRRP, or GLBP.
+ Network management protocols like telnet, SSH, SNMP, or RADIUS.

Therefore we must apply the CoPP to deal with SSH because it is in the
management plane. CoPP must be put under "control-plane" command.
insert code
  • ««
  • «
  • …
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download Cisco.350-401.v2022-12-29.q599 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.