Free Cisco 350-501 Exam Dumps Questions & Answers

Which wildcard is used with programmable APIs to Identify the values Cisco, Ciscotest, and CiscoSystems?

• A.  Cis?o
• B.  *Cisco
• C.  ?Cisco
• D.  Cisco *

SIMULATION 10
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab closes and cannot be reopened.
Topology

Tasks
Green future Service Provider has decided to implement ISIS in core network with dual-stack capability. As per Network design, it is Multi-Area ISIS configuration for IPv4 and IPv6. Routers in Western Area are in Area 49.0275 and Routers in Northern Area are in Area 49.0265. According to design guidelines, implement independent SPF calculation for IPv4 and IPv6. For future scalability, NW should also have wider metric fields to support MPLS Traffic Engineering when required. Below tasks to be achieved to complete the implementation.
1) Task 1
Configure appropriate interface of Western_R1 to establish ISIS adjacency with Northern_R2 for IPv4 and IPv6. Similarly, configure appropriate interface of Western_R4 to establish ISIS adjacency with Western_R4 for IPv4 and IPv6.
Note. Adjacency to be established with default level type.
2) Task 2
Enable ISIS multi-topology on Northen_R5 and Northern_R6 for address-family IPv6. Both routers should generate and accept new-style TLVs. This is to prepare the NW for future NW expansions such as MPLS traffic engineering.

An engineer is implementing a route map to support redistribution within BGP. The route map must be configured to permit all unmatched routes. Which action must the engineer perform to complete this task?

• A.  Remove the implicit deny entry.
• B.  Include a permit statement as the first entry.
• C.  Include a permit statement as the last entry.
• D.  Include at least one explicit deny statement.

Refer to the exhibit. During the last maintenance window, the network engineering team performed multiple software upgrades and enabled OSPFv3 for future use. However, when the network came up, the connection between HQ and the remote branch failed. A network engineer determined that routers R1 and R2 failed to establish an OSPFv2 adjacency. R1 was preconfigured with the point-to-point OSPF network type, and R2 as broadcast. The engineer confirmed that all connected interfaces are up, and the routers can reach one another via ICMP.
Which action must the engineer take to resolve the issue?

• A.  Set the same network statement under the OSPFv2 configuration on R1 and R2.
• B.  Set the R1 OSPFv2 process ID to match the R2 OSPFv2 process ID.
• C.  Change the hello and dead intervals on the interfaces on R1 and R2 to the same values respectively.
• D.  Configure R1 and R2 with the same OSPFv3 router ID.

Refer to the exhibit. A network engineer with an employee ID 4402:98:032 is setting up an IS-IS network with these requirements:
- Routes with a tag of 80 and IP prefixes other than 192.168.10.20/24
must be redistributed from Level 1 into Level 2
- Route leaking must be configured from Level 2 into the Level 1 domain for routes that are tagged with only 50 or 40 Which configuration must be implemented on RB to meet the requirements?

• A.  Remove match tag 40 from route-map leak2-1
• B.  Change match tag 80 to match tag 50 in route-map redist1-2
• C.  Add match ip address 152 in route-map redist1-2
• D.  Add match tag 80 in route-map leak2-1