A Cisco Unity Connection Administrator must set a voice mailbox so that is can be accessed form a secondary device. Which configuration on the voice mailbox makes this change?

• A.Alternate Names
• B.Mobile User
• C.Attempt Forward routing rule
• D.Alternate Extensions

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

Refer to the exhibit. Calls to Cisco Unity Connection are failing across Cisco Unified Border Element when callers try to select a menu prompt Why is this happening and how is it fixed?

• A.The Cisco Unity Connection Call Handler is configured for a "Release to Switch" transfer type Transfers must be disabled for the Cisco Unity Connection Call Handler
• B.Cisco Unified Border Element is sending the incorrect media IP address. The IP address of the loopback interface must be advertised in the SDP
• C.Cisco Unity Connection is configured on G.729 only. Cisco Unity Connection must be reconfigured to support iLBC.
• D.Cisco Unified Border Element is not sending any support for DTMF. OTMF configuration must be added to the appropriate dial peer.

Comment: *

Name: *

Email: *

Verification: *

A collaboration engineer must configure Cisco Unified Border Element to support up to five concurrent outbound calls across an Ethernet link with a bandwidth of 160 kb to the Internet Telephony Service Provider.
Which set of commands allows the engineer to complete the task without compromising voice quality?

• A.dial-peer voice 1 voip
  translation-profile outgoing Strip9
  max-conn 5
  destination-pattern 91[2-9]..[2-9]......$
  session protocol sipv2
  session target ipv4:142.45.10.1
  dtmf-relay rtp-nte sip-notify sip-kpml
• B.dial-peer voice 1 voip
  translation-profile outgoing Strip9
  max-conn 5
  destination-pattern 91[2-9]..[2-9]......$
  session protocol sipv2
  session target ipv4:142.45.10.1
  dtmf-relay rtp-nte sip-notify sip-kpml
  codec ilbc mode 20
• C.dial-peer voice 1 voip
  translation-profile outgoing Strip9
  max-conn 5
  destination-pattern 91[2-9]..[2-9]......$
  session protocol sipv2
  session target ipv4:142.45.10.1
  dtmf-relay rtp-nte sip-notify sip-kpml
  codec aacld
• D.dial-peer voice 1 voip
  translation-profile outgoing Strip9
  max-conn 5
  destination-pattern 91[2-9]..[2-9]......$
  session protocol sipv2
  session target ipv4:142.45.10.1
  dtmf-relay rtp-nte sip-notify sip-kpml
  codec mp4a-latm

Comment: *

Name: *

Email: *

Verification: *

What is the major difference between the two possible Cisco IM and Presence high-availability modes?

• A.Balanced mode provides user load balancing and user failover in the event of an outage. Active/standby mode provides an always on standby node in the event of an outage, and it also provides load balancing.
• B.Balanced mode provides user load balancing and user failover only for manually generated failovers.
  Active/standby mode provides an unconfigured standby node in the event of an outage, but it does not provide load balancing.
• C.Balanced mode provides user load balancing and user failover in the event of an outage. Active/standby mode provides an always on standby node in the event of an outage, but it does not provide load balancing.
• D.Balanced mode does not provide user load balancing, but it provides in the event of an outage. Active/ standby mode provides an always on standby node in the event of an outage, but it does not provide load balancing.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit. Given this "debug isdn q921" output, what is the problem with the PRI?

• A.Layer 1 is down on the controller.
• B.PRI does not have an IP address configured on the interface.
• C.Nothing, the PRI is sending keepalives.
• D.Layer 2 is down on the controller.

Comment: *

Name: *

Email: *

Verification: *