Free Access to CompTIA.N10-008.v2025-06-03.q684 with Valid Practice Test (Page 25)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
CompTIA Certification
N10-008 Exam
CompTIA.N10-008.v2025-06-03.q684 Dumps

««
«
…
20
21
22
23
24
25
26
27
28
29
…
»
»»

Question 116

Which of the following would MOST likely utilize PoE?

A.A camera
B.A printer
C.A hub
D.A modem

Correct Answer: A

A camera is most likely to utilize PoE (Power over Ethernet). PoE is a technology that allows electrical power to be delivered over Ethernet cables. It is used to power a variety of devices, such as cameras, phones, access points, and other networking equipment.Cameras are particularly well-suited for PoE because they are often installed in locations where it is difficult or impossible to run electrical power. By using PoE, cameras can be powered directly over the Ethernet cable, eliminating the need for separate power cables and outlets.Other devices, such as printers, hubs, and modems, are less likely to utilize PoE because they typically do not need to be powered over Ethernet. These devices are usually powered by AC (alternating current) power and are typically connected to a power outlet rather than an Ethernet cable.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 117

A technician needs to set up a wireless connection that utilizes MIMO on non-overlapping channels. Which of the following would be the best choice?

A.802.11a
B.802.11b
C.802.11g
D.802.11n

Correct Answer: D

802.11n is the best choice for setting up a wireless connection that utilizes MIMO on non-overlapping channels. 802.11n is a wireless standard that offers faster speeds and longer range than previous standards.
802.11n uses multiple-input multiple-output (MIMO) technology, which allows multiple antennas to transmit and receive multiple spatial streams of data simultaneously. MIMO can improve wireless performance, reliability, and capacity by exploiting multipath propagation and spatial diversity. 802.11n also uses non-overlapping channels in both the 2.4 GHz and 5 GHz frequency bands to avoid interference and increase bandwidth. Non-overlapping channels are channels that do not share any part of their frequency spectrum with other channels. References: [CompTIA Network+ Certification Exam Objectives], 802.11n - Wikipedia

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 118

Given the following information:

Which of the following command-line tools would generate this output?

A.netstat
B.arp
C.dig
D.tracert

Correct Answer: D

Explanation
Tracert is a command-line tool that traces the route of a packet from a source to a destination and displays the number of hops and the round-trip time for each hop. The output shown in the question is an example of a tracert output, which shows five hops with their IP addresses and hostnames (if available) and three latency measurements for each hop in milliseconds. References:
https://partners.comptia.org/docs/default-source/resources/comptia-network-n10-008-exam-objectives-(2-0),
https://www.lumen.com/help/en-us/network/traceroute/understanding-the-traceroute-output.html

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 119

Which of the following TCP ports is used by the Windows OS for file sharing?

A.53
B.389
C.445
D.1433

Correct Answer: C

Explanation
TCP port 445 is used by the Windows OS for file sharing. It is also known as SMB (Server Message Block) or CIFS (Common Internet File System) and allows users to access files, printers, and other shared resources on a network. References:
https://docs.microsoft.com/en-us/windows-server/storage/file-server/troubleshoot/detect-enable-and-disable-smb

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 120

A network requirement calls for segmenting departments into different networks. The campus network is set up with users of each department in multiple buildings. Which of the following should be configured to keep the design simple and efficient?

A.MDIX
B.Jumbo frames
C.Port tagging
D.Flow control

Correct Answer: C

Port tagging is a technique that involves adding a tag or identifier to the frames or packets that belong to a certain VLAN. A VLAN is a logical segment of a network that isolates traffic between different groups of devices. Port tagging allows devices on different physical ports or switches to communicate with each other as if they were on the same port or switch. Port tagging can help keep the design simple and efficient by reducing the number of physical ports and switches needed to segment departments into different networks. References:
https://www.comptia.org/blog/what-is-port-tagging

Comment: *

Name: *

Email: *

Verification: *

insert code

««
«
…
20
21
22
23
24
25
26
27
28
29
…
»
»»

[×]

Download PDF File

Enter your email address to download CompTIA.N10-008.v2025-06-03.q684 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter