Free Access to EMC.D-PWF-OE-00.v2026-10-30.q57 with Valid Practice Test (Page 3)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
EMC Certification
D-PWF-OE-00 Exam
EMC.D-PWF-OE-00.v2026-10-30.q57 Dumps

«
1
2
3
4
5
6
7
8
9
10
…
»
»»

Question 6

Which PowerFlex model includes integrated compute and storage in a single appliance?

A.PowerFlex R
B.PowerFlex Appliance
C.PowerFlex Rack
D.PowerFlex Manager

Correct Answer: B

PowerFlex Appliance is the model that offers a flexible, semi-customizable solution that includes both compute and storage resources within a single managed server node (Hyper-Converged Infrastructure).
PowerFlex Appliance: This offering allows customers to start small and scale. It provides the full PowerFlex software stack pre-installed on qualified hardware (like Dell PowerEdge R650/R750 nodes) that contributes both processing power (Compute) and disk capacity (Storage) to the cluster.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 7

Which operations are supported for managing snapshots in PowerFlex? (Choose two).

A.Restore data from a snapshot
B.Convert snapshots to writable volumes
C.Deduplicate snapshot data
D.Schedule automatic snapshot creation

Correct Answer: A,D

PowerFlex offers robust snapshot management capabilities accessible via the PowerFlex Manager UI, CLI (SCLI), and REST API.
Schedule automatic snapshot creation (Option D): PowerFlex supports Snapshot Policies.
Administrators can define policies that automatically generate snapshots at specific intervals (e.g., every hour, daily, or weekly) and define retention rules (how many snapshots to keep). This automation is critical for meeting Recovery Point Objectives (RPO) without manual intervention.
Restore data from a snapshot (Option A): PowerFlex allows administrators to restore a volume to a previous state using a snapshot. In the CLI, this is often handled by the command overwrite_volume_content, where the content of the production volume is replaced by the data in the snapshot. This is essential for recovering from data corruption or ransomware events.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 8

Which component is upgraded first during a PowerFlex cluster upgrade?

A.Metadata Managers
B.Storage Data Servers
C.Fault Sets
D.Cluster Nodes

Correct Answer: A

The order of operations for a PowerFlex upgrade is strict and dictated by the software architecture.
* Metadata Managers (MDM): The MDM is the "brain" of the cluster. It holds the cluster map and configuration. It must be upgraded first (Primary, then Secondary, then Tie-Breakers) so that it can understand the newer protocol versions and manage the upgrade of the subsequent components. An older MDM cannot manage a newer SDS.
* Storage Data Servers (SDS): Once the MDMs are upgraded, the storage nodes are upgraded one by one (or fault set by fault set).
* Storage Data Clients (SDC): Finally, the host-side drivers are updated.
Therefore, A (Metadata Managers) is the correct first step. Fault Sets (C) are logical groups, not software components to be upgraded.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 9

What is the minimum bandwidth requirement for replicating volumes between PowerFlex clusters?

A.1 Gbps
B.10 Mbps
C.100 Mbps
D.10 Gbps

Correct Answer: C

100 Mbps: While PowerFlex replication is highly efficient and only sends unique data chunks (deltas), the supported minimum reliable bandwidth for a WAN link between clusters is typically
100 Mbps.
Reasoning: Below this speed, even moderate change rates in a production database would likely cause the replication journal to fill up faster than data can be drained to the remote site. This would lead to a "Buffer Full" state, causing the replication to pause or the system to lose its Recovery Point Objective (RPO) compliance.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 10

What actions can be taken as part of post-installation tasks in PowerFlex? (Choose two).

A.Configure protection domains
B.Assign VLANs to nodes
C.Enable fault sets
D.Define replication targets

Correct Answer: A,C

"Post-installation" refers to the steps taken after the base software (MDM/SDS) is installed but before the system is fully operational for production I/O.
Configure Protection Domains (Option A): This is step #1. You must define the logical boundaries of your storage.
Enable Fault Sets (Option C): This is a critical configuration step that typically happens during the setup of the Protection Domain structure. If you intend to use Fault Sets (for rack awareness), you should enable and define them before populating the system with massive amounts of data, as converting to a Fault Set structure later is operationally complex.

Comment: *

Name: *

Email: *

Verification: *

insert code

«
1
2
3
4
5
6
7
8
9
10
…
»
»»

[×]

Download PDF File

Enter your email address to download EMC.D-PWF-OE-00.v2026-10-30.q57 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter