Free Access to EMC.D-XTR-DY-A-24.v2024-11-11.q38 with Valid Practice Test (Page 7)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
EMC Certification
D-XTR-DY-A-24 Exam
EMC.D-XTR-DY-A-24.v2024-11-11.q38 Dumps

«
1
2
3
4
5
6
7
8
9
»

Question 26

What is the recommended way to check connectivity of DAE controllers, IB switches, IPMI, and BBU on an XtremIO X1 multi X-Brick after software installation and before cluster creation?

A.Use the WebUl
B.Use the Easy-Install menu
C.Use the Technician Advisor Tool
D.Use the XMCLI

Correct Answer: D

The recommended way to check the connectivity of DAE controllers, IB switches, IPMI, and BBU on an XtremIO X1 multi X-Brick after software installation and before cluster creation is to use the XMCLI (XtremIO Management Command Line Interface). The XMCLI provides commands to test connectivity and confirm that all components are healthy and connected within the cluster. Here are the steps:
Access XMCLI: Log into the XtremIO Management Server (XMS) and access the XMCLI.
Run Connectivity Tests: Use the test-xms-storage-controller-connectivity command to check the connectivity of the storage controllers. Similar commands are available for other components1.
Review Test Results: Analyze the output of the commands to ensure that there is no packet loss and that the response times are within acceptable limits.
Troubleshoot if Necessary: If any connectivity issues are detected, use the XMCLI to troubleshoot and resolve them before proceeding with the cluster creation.
Document the Process: Keep a record of the connectivity checks and any actions taken to resolve issues as part of the installation documentation.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 27

When an XtremIO X2 array is delivered, where is the cable shown in the exhibit connected?

A.Middle USB in X3-SC1 only
B.Bottom USB in X3-SC1 only
C.Bottom USB in X3-SC1 and X3-SC2
D.Middle USB in X3-SC1 and X3-SC2

Correct Answer: D

When an XtremIO X2 array is delivered, the cable shown in the exhibit should be connected to the middle USB ports in both X3-SC1 and X3-SC2. This is based on the standard configuration and setup for XtremIO X2 arrays as per the Dell XtremIO Deploy Achievement document. The middle USB ports are typically used for specific functions such as connecting to a management network or interfacing with other devices that are part of the storage array infrastructure.
The process for connecting the cable is as follows:
* Identify the Correct Ports: Locate the middle USB ports on both X3-SC1 and X3-SC2. These ports are usually marked and differentiated from other USB ports by their position or labeling.
* Connect the Cable: Insert the USB connector end of the cable into the middle USB port on X3-SC1 and then connect the other end to the corresponding port on X3-SC2. Ensure that the connection is secure and that the cable is not obstructing any other components or airflow.
* Verify the Connection: Once connected, verify that the cable is recognized by the system. This can typically be done through the XtremIO Management Server (XMS) interface or by checking the system's hardware configuration.
* Check for Functionality: Ensure that the connected cable functions as intended. This may involve transferring data or accessing the management network, depending on the specific use case for the cable.
* Reference Official Documentation: For detailed instructions and best practices, always refer to the official Dell XtremIO Deploy Achievement document1. This document provides comprehensive guidance on all aspects of setting up and managing XtremIO X2 arrays, including cable connections.
By following these steps and referring to the official documentation, you can ensure that the cable is connected correctly and that the XtremIO X2 array is set up for optimal performance and management.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 28

What is the total number of power connectors that must be available in a customer rack for an XtremIO X2 dual X-Brick cluster configuration without a physical XMS installed?

A.10
B.8
C.18
D.16

Correct Answer: D

* Power Connectors for XtremIO X2 Dual X-Brick Configuration: Each X-Brick typically requires multiple power connections for redundancy and reliability. A dual X-Brick configuration without a physical XMS would need to account for these requirements.
* Calculation:
* Each X-Brick has 2 storage controllers, each requiring 2 power connections, totaling 4 power connections per X-Brick.
* For a dual X-Brick configuration: 4 power connections per X-Brick * 2 X-Bricks = 8 power connections.
* Each DAE (Disk Array Enclosure) typically requires 2 power connections. In a dual X-Brick setup, there are 4 DAEs, totaling 8 power connections.
* Total power connections: 8 (for X-Bricks) + 8 (for DAEs) = 16 power connections.
References:
* Dell XtremIO X2 Installation Guide
* XtremIO User Guide
* Dell XtremIO Deployment Services

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 29

A systems administrator's VMware Horizon environment consists of 1000 linked clones. Based on best practices, what is the minimum number of datastores required to support this configuration connected to XtremIO?

A.6
B.4
C.8
D.10

Correct Answer: A

* VMware Horizon environments with linked clones require optimal storage configurations for performance and management.
* According to best practices, each datastore should handle a specific number of linked clones to avoid performance bottlenecks.
* For 1000 linked clones, it is recommended to have a minimum of 6 datastores to distribute the load evenly and maintain optimal performance.
References:
* Dell XtremIO Best Practices for VMware Horizon
* VMware Horizon Architecture Guide

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 30

During the installation of an XtremlO cluster, you configure the ESRS server using a FQDN for Connect Home. During the test, you discover that the XtremlO cluster fails to connect home. What is a possible cause for this issue?

A.ESRS IP for an ESRS configuration can only be used
B.DNS needs to be configured on the ESRS Gateway
C.Port 25 is blocked on the firewall
D.DNS needs to be configured on the XMS

Correct Answer: D

The XtremIO Management Server (XMS) requires DNS configuration to resolve Fully Qualified Domain Names (FQDN) used in ESRS (Electronic Support Services) configurations. If the DNS is not configured on the XMS, it will not be able to resolve the ESRS FQDN, leading to a failure in connecting home. Configuring DNS on the XMS ensures that all network addresses, including the ESRS server, can be resolved correctly.
References:
* Dell XtremIO Deployment and Learning Course Materials
* XtremIO X2 Configuration Guide

Comment: *

Name: *

Email: *

Verification: *

insert code

«
1
2
3
4
5
6
7
8
9
»

[×]

Download PDF File

Enter your email address to download EMC.D-XTR-DY-A-24.v2024-11-11.q38 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter