FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. F5 Certification
  3. F5CAB4 Exam
  4. F5.F5CAB4.v2026-06-15.q69 Dumps
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
Download Now

Question 11

What is the tmsh command to list the IP ranges that can access the management interface via SSH? (Choose one answer)

Correct Answer: B
On BIG-IP systems, SSH access restrictions are configured under the /sys sshd object. The allow property defines the IP addresses or networks permitted to connect to the management interface using SSH.
The list command is used to display the current configuration settings.
Therefore, tmsh list /sys sshd allow correctly displays the configured allowed IP ranges.
insert code

Question 12

A BIG-IP Administrator needs to find which modules have been licensed for use on the BIG-IP system. In which section of the Configuration Utility can the BIG-IP Administrator find this information?

Correct Answer: B
Identifying the current device status includes knowing which software modules (such as LTM, ASM, or APM) are active and how much hardware resource (CPU/Memory) is allocated to them.
The System > Resource Provisioning screen displays the licensing status and allows the administrator to set the provisioning level (Nominal, Dedicated, or Minimum) for each module.
insert code

Question 13

A BIG-IP device sends out the following SNMP trap: big-ipo.f5.com - bigipExternalLinkChange Link: 1.0 is DOWN. Where in the BIG-IP Configuration utility should the BIG-IP Administrator verify the current status of Link 1.0?

Correct Answer: C
Comprehensive and Detailed Explan13ation From BIG-IP Administration Control Plane Administration documents: Monitoring the physical status of the device is critical for reporting device health. In F5 nomenclature, "1.0", "1.1", etc., represent physical hardware interfaces. To verify if a physical link is up or down as reported by the Control Plane's SNMP agent, the administrator must check the Interface List located under Network > Interfaces
insert code

Question 14

Which interface is used for out-of-band management?

Correct Answer: C
The dedicated management interface is used for administrative access.
insert code

Question 15

Refer to the exhibit.

The BIG-IP Administrator is investigating disk utilization on the BIG-IP device. What should the BIG-IP Administrator check next? (Choose one answer)

Correct Answer: C
When troubleshooting a BIG-IP system where a partition is reported as full (100% utilization), identifying and removing large or unnecessary files is the immediate next step for restoration of system stability.
* Symptoms of Full Partitions : If a file system (such as the root / or /var) becomes full, it can result in unpredictable system behavior, failure to save configurations, and the inability to log in to the Web UI.
* The Root (/) Partition : This partition is intentionally kept small on F5 systems. It is highly sensitive to the storage of third-party software or diagnostic files that should ideally be stored in the /shared or /var directories.
* Procedural Resolution : To resolve 100% disk usage, administrators should check for large files on the affected partition using CLI commands like du -ah or find / -xdev -type f -exec du {} \; | sort -rn | head
-20.
* Common Culprits : Large files typically causing these issues include old core files, tech support bundles, large diagnostic logs (packet diags), or temporary files created during administrative tasks.
* Diagnostics vs. Remediation : While tests like the EUD (End User Diagnostics) or platform diagnostics are useful for hardware verification, they do not resolve file system exhaustion issues that have already reached a critical 100% state.
insert code
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download F5.F5CAB4.v2026-06-15.q69 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.