Free Access to Fortinet.NSE6_FSW-7.2.v2025-11-03.q40 with Valid Practice Test (Page 8)

Question 31

Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

A.Enable the IGMP flood setting on the static port for all multicast groups.
B.Enable the IGMP flood reports setting on the mRouter port.
C.Enable IGMP snooping proxy.
D.Enable IGMP flood unknown multicast traffic on the global setting.

Question 32

Refer to the exhibits

Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)

A.Add the MAC address of PCI as a member of VLAN 10.
B.Add VLAN ID 10 as a member of the untagged VLANs on port1.
C.Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.
D.Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.

Question 33

Refer to the exhibit.

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

A.FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.
B.Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.
C.DHCP clients that are trusted by DHCP snooping configured is only one.
D.Maximum value to accept clients DHCP request is configured as per DHCP server range.

Question 34

Refer to the exhibit.

The exhibit shows the current status of the ports on the managed FortiSwitch. Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

A.A standalone switch with the shown serial number is connected on port23.
B.port23 is a member of a trunk that uses the Access-1 FortiSwitch serial number as the name of the trunk.
C.port23 is configured as the dedicated management interface.
D.Ports connected to adjacent FortiSwitch devices show their serial number as the native VLAN.

Question 35

Refer to the exhibit.

The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports, and these ports are connected to endpoints which are powered by PoE.
Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?

A.Create new a LLDP-MED application type to define the PoE parameters.
B.Assign a new LLDP profile to handle different LLDP-MED TLVs.
C.Define an LLDP-MED location ID to use standard protocols for power.
D.Add power management as part of LLDP-MED TLVs to advertise.

Correct Answer: D

To cause endpoints to exchange PoE information and negotiate power with the managed FortiSwitch via LLDP, you should configure the LLDP profile to include power management in the advertised LLDP-MED TLVs. Here are the steps:
Access the LLDP Profile Configuration:
Start by entering the LLDP profile configuration mode with the command:
config switch-controller lldp-profile
edit "LLDP-PROFILE"
Enable MED-TLVs:
Ensure that MED-TLVs (Media Endpoint Discovery TLVs) are enabled. These TLVs are used for extended discovery relating to network policies, including PoE, and are essential for PoE negotiation. They include power management which is crucial for the negotiation of PoE parameters between devices. The command to ensure network policies are set might look like:
set med-tlvs network-policy
Add Power Management TLV:
Specifically add or ensure the power management TLV is part of the configuration. This will advertise the PoE capabilities and requirements, enabling dynamic power allocation between the FortiSwitch and the connected devices (like VoIP phones or wireless access points). This can typically be done within the network-policy settings:
config med-network-policy
edit <policy_index>
set poe-capability
next
end
Save and Apply Changes:
Exit the configuration blocks properly ensuring changes are saved:
End
Verify Configuration:
It's always good practice to verify that your configurations have been applied correctly. Use the appropriate show or get commands to review the LLDP profile settings.
By adding the power management as part of LLDP-MED TLVs, the FortiSwitch will be able to communicate its power requirements and capabilities to the endpoints, thereby facilitating a dynamic power negotiation that is crucial for efficient PoE utilization.
Reference:
For more detailed information and additional configurations, you can refer to the FortiSwitch Managed Switches documentation available on Fortinet's official documentation site: Fortinet Product Documentation

Question 31

Question 32

Question 33

Question 34

Question 35

Download PDF File