An LDAP user cannot authenticate against a FortiGate device. Examine the real time debug output shown in the exhibit when the user attempted the authentication; thenanswer the question below.


Based on the output in the exhibit, what can cause this authentication problem?

• A.The FortiGate has been configured with thewrong password for the LDAP administrator.
• B.The FortiGate has been configured with the wrong authentication schema.
• C.User student is not found in the LDAP server.
• D.User student is using a wrong password.

Comment: *

Name: *

Email: *

Verification: *

Which statement is true regarding File description (FD) conserve mode?

• A.A FortiGate enters FD conserve mode when the amount of available description is less than 5%.
• B.FD conserve mode affects all daemons running on the device.
• C.IPS inspection is affected when FortiGate enters FD conserve mode.
• D.Restarting the WAD process is required to leave FD conserve mode.

Comment: *

Name: *

Email: *

Verification: *

View the exhibit, which contains the partial output of an IKE real-time debug, and then answer the question below.

Which statements about this debug output are correct? (Choose two.)

• A.It showsa phase 1 negotiation.
• B.The remote gateway IP address is 10.0.0.1.
• C.The initiator has provided remote as its IPsec peer ID.
• D.The negotiation is using AES128 encryption with CBC hash.

Comment: *

Name: *

Email: *

Verification: *

Which of the following statements is true regarding a FortiGate configured as an explicit web proxy?

• A.FortiGate limits the number of simultaneous sessions per explicit web proxy user. This limit CANNOT be modified by the administrator.
• B.FortiGate limits the total number of simultaneous explicit web proxy users.
• C.FortiGate limits the number of simultaneous sessions per explicit web proxy user The limit CAN be modified by the administrator
• D.FortiGate limits the number of workstations that authenticate using the same web proxy user credentials. This limit CANNOT be modified by the administrator.

Comment: *

Name: *

Email: *

Verification: *

Examine the following partial outputs from two routing debug commands; then answer the question below.
# get router info kernel
tab=254 vf=0 scope=0type=1 proto=11 prio=00.0.0.0/0.0.0.0/0->0.0.0.0/0 pref=0.0.0.0 gwy=10.200.1.254 dev=2(port1) tab=254 vf=0 scope=0type=1 proto=11 prio=10 0.0.0.0/0.0.0.0/0->0.0.0.0/0 pref=0.0.0.0 gwy=10.200.2.254 dev=3(port2) tab=254 vf=0 scope=253type=1 proto=2 prio=0 0.0.0.0/0.0.0.0/.->10.0.1.0/24 pref=10.0.1.254 gwy=0.0.0.0 dev=4(port3)
# get router info routing-table all s*0.0.0.0/0 [10/0] via 10.200.1.254, portl [10/0] via 10.200.2.254, port2,
[10/0] dO.0.1.0/24 is directly connected, port3 dO.200.1.0/24 is directly connected, portl d0.200.2.0/24 is directly connected, port2 Which outbound interface or interfaces will be used by this FortiGate to route web traffic from internal users to the Internet?

• A.port!
• B.Both portl and port2.
• C.port3.
• D.port2.

Comment: *

Name: *

Email: *

Verification: *