FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • IBM
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • IBM
    IBM
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. HP Certification
  3. HPE2-W09 Exam
  4. HP.HPE2-W09.v2023-11-15.q73 Dumps
  • ««
  • «
  • …
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • …
  • »
  • »»
Download Now

Question 31

A customer's servers use ISCSI, and they send data and storage traffic on the same pair of I OGbE links. Is this a best practice for supporting the ISCSI requirements?
Solution: Set up dedicated switches to connect to iSCSl arrays. Connect top of rack (ToR) switches, which will support both data and storage traffic, to those dedicated switches.

Correct Answer: B
insert code

Question 32

A data center has a three-tier topology with ArubaOS-CX switches at each layer, is this a use case for implementing Virtual Switching Extension (VSX) at the core?
Solution: The aggregation layer operates at Layer 2 only, and the core provides Layer 2 and Layer 3 functions.

Correct Answer: B
The aggregation layer operates at Layer 2 only, and the core provides Layer 2 and Layer 3 functions is not a use case for implementing Virtual Switching Extension (VSX) at the core for a data center that has a three-tier topology with ArubaOS-CX switches at each layer. VSX is a feature that provides active-active forwarding and redundancy for ArubaOS-CX switches. VSX can be implemented at any layer of the data center network, but it is more common to implement it at the aggregation or leaf layer, where it can provide Layer 2 and Layer 3 functions. The core layer typically operates at Layer 3 only and does not require VSX2.
insert code

Question 33

Is this how you should position switches in the ArubaOS-CX portfolio tor data center networks?
Solution: Deploy Aruba 83xx switches as core switches for very large three-tier data center networks.

Correct Answer: A
insert code

Question 34

Two ArubaOS-CX switches ate part of a Virtual Switching Extension (V5X) fabric. Is this a guideline for configuring the switches' link-up delay settings?
Solution: The link-up delay timer is only required when split-recovery is disabled.

Correct Answer: B
Virtual Switching Extension (VSX) is a high-availability technology that allows two ArubaOS-CX switches to operate as a single logical device. VSX link-up delay is a feature that delays bringing downstream VSX links up, following a VSX device reboot or an ISL flap. This prevents traffic blackholing or loops due to transient conditions. The link-up delay timer is not only required when split-recovery is disabled. Split-recovery is another feature that prevents traffic blackholing or loops when the ISL link fails and then recovers. Split-recovery works by disabling the secondary VSX member's downstream links until it synchronizes with the primary member. However, split-recovery does not cover all scenarios where traffic blackholing or loops can occur, such as when both VSX members reboot simultaneously or when the ISL flaps rapidly. Therefore, it is recommended to configure the link-up delay timer even when split-recovery is enabled1. Therefore, this is not a valid guideline for configuring the switches' link-up delay settings.
insert code

Question 35

Is this a use case for disabling split-recovery mode on ArubaOS-CX switches in a Virtual Switching Extension (VSX) fabric?
Solution: You want to prevent any possibility of a split brain situation from occurring if the keepalive link fails some time after the ISL.

Correct Answer: A
Split-recovery mode is a feature of ArubaOS-CX that prevents traffic loss when the ISL goes out-of-sync and keepalive subsequently fails12. This can happen if the ISL is restored after a failure but the VSX nodes are not synchronized. Split-recovery mode enables the secondary switch to restore its VSX LAGs after 10 keepalive packets are missed, approximately 10 seconds after keepalive goes down2. This avoids a split brain situation where both switches act as primary and forward traffic independently, causing loops and duplicate packets1. Therefore, disabling split-recovery mode is not a use case for preventing split brain situations, and the correct answer is yes. For more information on split-recovery mode and VSX, refer to the Aruba Data Center Network Specialist (ADCNS) certification datasheet3 and the Virtual Switching Extension (VSX) Guide for your switch model2.
insert code
  • ««
  • «
  • …
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download HP.HPE2-W09.v2023-11-15.q73 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.