Free HP HPE6-A48 Exam Dumps Questions & Answers

Refer to the exhibit.

A 7008 Branch Office Controller (BOC) is deployed in a remote office behind a core router. This core router does not support 802.1q encapsulation. The Mobility Controller (MC) is the gateway for two tunneling mode SSIDs, as shown in the exhibit.
Which two different configuration options ensure that wireless users are able to reach the branch network through the router? (Select two.)

• A.  Configure all ports of the BOC as access ports on the controller VLAN, and change the gateway of clients to the core router IP.
• B.  Configure the uplink of the BOC as a trunk port, tagging the controller and the SSID VLANs, and enable NAT for the SSID VLANs.
• C.  Configure the uplink of the BOC as an access port on the controller VLAN, and enable NAT for the SSID VLANs.
• D.  Configure the uplink of the BOC as a trunk port that permits the controller and the SSID VLANs. The controller VLAN must be native.
• E.  Configure the uplink of the BOC as an access port on the controller VLAN, and add static router in the router for the SSID VLAN subnets.

Refer to the exhibit.

A company acquires ten barcode scanners to run inventory tasks. These Wifi devices support WPA2-PSK security only. The network administrator deploys a WLAN named scanners using the configuration shown in the exhibit.
What must the network administrator do next to ensure that the scanner devices successfully connect to their SSID?

• A.  Set internal as the MAC authentication server group.
• B.  Enable L2 Authentication Fail Through.
• C.  Add scanner MAC addresses in the internal database.
• D.  Add scanner MAC addresses in user derivation rules.

Refer to the exhibit.

A network administrator deploys a Mobility Master (MM)-Mobility Controller (MC) solution in the headquarters. The network administrator prepares the wired side of the network with the proper VLAN, DHCP settings, and routing services to ensure that APs can reach the MCs.
The network administrator connects two APs in different IP segments and waits for 20 minutes, but SSIDs are advertised in one of the APs only. The engineer logs into the MC console and sees the output shown in the exhibit.
What is the reason that the AP20 is not broadcasting SSIDs?

• A.  PAPI traffic is being blocked.
• B.  GRE traffic is being blocked.
• C.  IPSec traffic is being blocked.
• D.  IKE traffic is being dropped.

Refer to the exhibit.

A network administrator configures a Mobility Master (MM)-Mobility Controller (MC) solution and integrates it with AirWave. The network administrator configures the SNMP and terminal credentials in the MM and MC, and then monitors the mobility devices from AirWave, including Clarity for user association and basic network services verification. However, AirWave does not display any UCC data that is available in the MM dashboard.
Based on the information shown in the exhibit, which configuration step should the network administrator do next in the MM to complete the integration with AirWave?

• A.  Verify the papi-security key in the AMP profile.
• B.  Enable the inline network services statistics in the AMP profile.
• C.  Define AirWave as a management server in the MM.
• D.  Enable UCC monitoring in the AMP profile.

During master controller redundancy and failover, these steps occur:
1. Master 1 acts as the primary master and it goes down, therefore, Master 2 takes over as primary.
2. Master 1 comes back up again (reboots).
3. Master 2 continues to be the active master.
Based on this scenario, how is master redundancy configured on the controller?

• A.  Preemption enabled, Set VRRP priority of Master 1 as 110 and the priority of master 2 as 100.
• B.  Preemption disabled, Set VRRP priority of Master 1 and master 2 as default.
• C.  Preemption disabled, Set VRRP priority of Master 1 as 110 and the priority of master 2 as 100.
• D.  Preemption enabled, Set VRRP priority of Master 1 and master 2 as default.