Free Access to Huawei.H35-480_V3.0.v2024-01-08.q39 with Valid Practice Test (Page 2)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
SAP
EMC
PMI
HP
Salesforce

Home
Huawei Certification
H35-480_V3.0 Exam
Huawei.H35-480_V3.0.v2024-01-08.q39 Dumps

«
1
2
3
4
5
6
7
8
9
»

Question 1

Which of the following MML commands can be used to query version information relating to the software stored on the gNodeB?

A.LST VER
B.DSP SOFTWARE
C.LST SOFTWARE
D.LST PATCH

Correct Answer: C

The correct MML command to query version information relating to the software stored on the gNodeB is LST SOFTWARE. This command will list the version information of the software installed on the gNodeB, including the version numbers, software names, and more. This is stated in the official Huawei documentation, which states: "Use the LST SOFTWARE command to check the version information of the software installed on the gNodeB, including the version numbers, software names, and more." Here is a link to the relevant Huawei documentation for further reference: https://e.huawei.com/en/products/base-station/bbu5900/overview

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 2

After the NR base station commissioning is complete and before services go online, which of the following must be set for the NE status?

A.Normal
B.New
C.Upgrade
D.Testing

Correct Answer: A

According to the Huawei SA Networking Product Design Guide (https://www.huawei.com/en/doc/e_huaweidoc/pdf/HW_051525), after the NR base station commissioning is complete and before services go online, the NE status must be set to 'Normal'.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 3

At which layer is downlink data split implemented over the NR air interface in the NSA Option 3x architecture?

A.RLC layer
B.MAC layer
C.PDCP layer
D.Physical layer

Correct Answer: B

Downlink data split over the NR air interface in the NSA Option 3x architecture is implemented at the medium access control (MAC) layer. The MAC layer is responsible for the management of data transmission over the air interface, including segmentation and reassembly of data packets, scheduling of transmission resources, and error correction. The other layers (RLC, PDCP, and physical) are not involved in the implementation of downlink data split.
https://ec.europa.eu/research/participants/documents/downloadPublic?documentIds=080166e5a964aa85&appId=PPGMS Preliminary results for multi-service support in link solution adaptation
https://ec.europa.eu/research/participants/documents/downloadPublic?documentIds=080166e5a964aa85&appId=PPGMS
https://ieeexplore.ieee.org/iel7/6287639/8948470/08998153.pdf
3GPP NR Sidelink Transmissions Toward 5G V2X
https://ieeexplore.ieee.org/iel7/6287639/8948470/08998153.pdf
https://www.3gpp.org/ftp/Inbox/Marcoms/ICT_6_1-2.pdf
journal of ict standardization - 3gpp
https://www.3gpp.org/ftp/Inbox/Marcoms/ICT_6_1-2.pdf
In the Non-Stand-Alone (NSA) Option 3x architecture, the control plane functions are handled by the 4G LTE network (EPC), while the user plane functions are handled by the 5G NR network. Data split is a technique that allows to split the user plane data between the 4G LTE and 5G NR networks.
The MAC (Medium Access Control) layer is responsible for controlling the access to the shared wireless medium, and it is where the downlink data split is implemented. In this architecture, the MAC layer in the 5G NR network receives the downlink data from the 4G LTE network and sends it to the physical layer for transmission.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 4

Which of the following can be used to check whether an antenna is reversely connected during NR single site verification?

A.Transmission test
B.DT around the site
C.Fixed-point CQT
D.VSWR test

Correct Answer: A

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 5

Which of the following is the correct sequence for adding gNodeB hardware?

A.Subrack -> Board -> Cabinet -> RF unit
B.Cabinet -> Subrack -> Board -> RF unit
C.RF unit -> Subrack -> Board -> Cabinet
D.Board -> Cabinet -> Subrack -> RF unit

Correct Answer: C

Comment: *

Name: *

Email: *

Verification: *

insert code

«
1
2
3
4
5
6
7
8
9
»

[×]

Download PDF File

Enter your email address to download Huawei.H35-480_V3.0.v2024-01-08.q39 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2025 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter