Free IBM 000-109 Exam Dumps Questions & Answers

An administrator has a Power 720 with 64GB of memory and Active Memory Expansion (AME).
An LPAR has only 10GB of memory available and an application has been sized at 15GB of memory. The administrator runs amepat to determine an efficient expansion factor. Based on the output, an expansion factor of 1.6 has been chosen.
How should this be configured in the LPAR?

• A.  Enter 10GB as 'desired', enter 1.6 in the Active memory expansion factor field.
• B.  Enter 16GB as 'desired' and modify/etc/ame.conf with AME_RATIO=1.6.
• C.  Enter 10GB as 'desired' and modify/etc/ame.conf with AME_RATIO=1.6.
• D.  Enter 16GB as 'desired', enter 1.6 in the Active memory expansion factor field.

An administrator wants to add vSCSI adapters to a new client using the existing mapping schema. The slots will be 40/41 on the VIO Server. Given the current properties of the VIO server, what must be done to accomplish this?

• A.  Change the Maximum virtual adapters to 50 in the VIOS partition profile.
  Create the vSCSI adapters on slots 40/41 in the VIOS partition profile and map them as
  "Any client partition can connect".
  Reboot the VIOS.
• B.  Use DLPAR to increase the Maximum virtual adapters to 50.
  Use DLPAR to create the vSCSI adapters on slots 40/41 and map them as "Any client
  partition can connect".
• C.  Use DLPAR to increase the Maximum virtual adapters to 50.
  Use DLPAR to create the vSCSI adapters on slots 40/41 and map them to the new client.
• D.  Change the Maximum virtual adapters to 50 in the VIOS partition profile.
  Create the vSCSI adapters on slots 40/41 in the VIOS partition profile and map them to the
  new client.
  Shutdown and reactivate the VIOS.

An administrator would like to determine the virtualization capabilities of some attached storage before proposing a new virtualization strategy. To determine the capabilities of the attached storage, the administrator runs chkdev and receives the following result:
padmin:vio1:/home/padmin>chkdev -dev hdisk1 NAME: hdisk1 IDENTIFIER: 382136005076801710072480000000000791F04214503IBMfcp PHYS2VIRT_CAPABLE: NA VIRT2NPIV_CAPABLE: YES VIRT2PHYS_CAPABLE: YES
Based on the output above, which one of the statements is true?

• A.  The disk is presented by vSCSI and is NPIV capable.
• B.  The disk can only be presented as a physical disk.
• C.  The disk can be presented by NPIV only.
• D.  The disk can be converted to NPIV with data loss.

A secondary site is being deployed for application availability and site failover. Servers of identical model and type have been ordered and delivered to the new location.
Additional PowerVM activation keys were obtained for the original location to allow more than 32000 WWNs and enable Active Memory Sharing (AMS).
How can the duplicate systems be updated to enable these additional features?

• A.  The activation keys must be exported using the PowerVM option within the Capacity On Demand (CoD) panel on the HMC.
• B.  Contact IBM Support to generate the one-time password required to administer the PowerVM activation keys.
• C.  Activation keys are generated for a specific system and must be generated for each new server in the failover site.
• D.  Create a system plan of the existing configuration and deploy this to the duplicate configuration.

An administrator adds a new virtual target device to a vhost adapter that already had target devices on it. The client LPAR does not detect the new disk and the following error has been logged in the errlog:

What is the most likely cause for this situation?

• A.  The intr_priority of the host adapter is set lower than that needed by the new drive.
• B.  The max_transfer parameter of the new drive is smaller than the rate already reported by the host adapter
• C.  The queue_depth parameter of the new drive is larger than those of the other drives provided by the host adapter
• D.  The intr_lsi of the host adapter is set higher than that needed by the new drive