FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. Juniper Certification
  3. JN0-280 Exam
  4. Juniper.JN0-280.v2025-04-14.q61 Dumps
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
Download Now

Question 11

What is a key characteristic of traditional multi-tier data center architectures?

Correct Answer: B
insert code

Question 12

What is a VLAN?

Correct Answer: D
insert code

Question 13

Which command on a router is used to view the current routing table?

Correct Answer: A
insert code

Question 14

Within your router, you want to verify that you are learning routes from a remote BGP peer at IP address
10.10.100.1. Which command would satisfy the requirement?

Correct Answer: A
To verify that your router islearning routes from a remote BGP peerat a specific IP address (e.g.,
10.10.100.1), the correct command to use is show route receive-protocol bgp.
Step-by-Step Breakdown:
* BGP Route Learning:The show route receive-protocol bgp command displays the routes that have been received from a specified BGP peer. This helps in confirming that the remote peer is sending routes correctly and that your router is receiving them.
* Command Example:
show route receive-protocol bgp 10.10.100.1
* This will show all routes that have been received from the BGP peer with IP address 10.10.100.1.
Juniper Reference:
* BGP Route Verification: Use this command to troubleshoot and verify that routes from a specific BGP peer are being received.
insert code

Question 15

Which operation mode command will display the mapping between the VLAN ID and ports on a switch?

Correct Answer: D
To display themapping between VLAN IDs and portson a Juniper switch, the show vlans command is used.
Step-by-Step Breakdown:
* VLAN Information:The show vlans command displays detailed information about VLAN configurations, including the VLAN ID, associated interfaces (ports), and VLAN membership.
* Command Example:
show vlans
* This command will provide an output listing each VLAN, its ID, and the interfacesassociated with the VLAN, enabling network engineers to quickly verify VLAN to port mappings.
Juniper Reference:
* VLAN Verification: Use the show vlans command to verify which VLANs are configured on the switch and the ports that are members of those VLANs.
insert code
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download Juniper.JN0-280.v2025-04-14.q61 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.