Free Microsoft 70-741 Exam Dumps Questions & Answers

You have a virtual machine named VM1 that runs Windows Server 2016, VM1 hosts a service that requires high network throughput.
VM1 has a virtual network adapter that connects to a Hyper-V switch named vSwitch1. vSwitch1 has one network adapter. The network adapter supports Remote Direct Memory Access (RDMA), the single root I/O virtualization (SR-IOV) interface, Quality of Service? (QoS), and Receive Side Scaling (RSS).
You need to ensure that the traffic from VM1 can be processed by multiple networking processors.
Which Windows PowerShell command should you run on the host of VM1?

• A.  Set-NetAdapterRdma
• B.  Set-NetAdapterRss
• C.  Set-NetAdapterQos
• D.  Set-NetAdapterSriov

Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
Refer to exhibit:

Server1 has two virtual machines named VM1 and VM that run Windows Server 2016. VM1 connects to Private1. VM2 has two network adapters.
You need to ensure that VM1 connects to the corporate network by using NAT.
Solution: You connect VM2 to Private1 and External1. You install the Remote Access server on VM2, and you configure NAT in the Routing and Remote Access console. You configure VM1 and VM2 as the default gateway.
Does this meet the goal?

• A.  Yes
• B.  No

You have a server named Server1 that runs Windows Server 2016. Server1 is a Hyper-V host that hosts a virtual machine named VM1.
Server1 has three network adapter cards that are connected to virtual switches named vSwitch1, vSwitch2 and vSwitch3.
You configure NIC Teaming on VM1 as shown in the exhibit. (Click the Exhibit button.)

You need to ensure that VM1 will retain access to the network if a physical network adapter card fails on Server1.
What should you do?

• A.  From Windows PowerShell on VM1, run the Set-VmNetworkAdapterTeamMapping cmdlet.
• B.  From Windows PowerShell on Server1, run the Set-VmSwitch cmdlet.
• C.  From Windows PowerShell on Server1, run the Set-VmNetworkAdapterFailoverConfiguration cmdlet
• D.  From Windows PowerShell on Server1, run the Set-VmNetworkAdapter cmdlet.

You have two servers named Server1 and Server2 that run Windows Server 2016. Both servers have the DHCP Server server role installed.
Server1 has a DHCP scope named Scope1. Server2 has a DHCP scope named Scope2.
You need to ensure that client computers can get an IP address if a single DHCP server fails. You must be able to control the percentage of requests to which each DHCP server responds during normal network operations.
What should you do?

• A.  Add Server1 and Server2 as nodes in a failover cluster, and then configure the quorum mode.
• B.  Add Server1 and Server2 as nodes in a failover cluster, and then configure the DHCP Server server role.
• C.  Add Server1 and Server2 as nodes in a failover cluster, and then configure port rules for UDP 67 and UDP 68.
• D.  On Server1 and Server2, configure DHCP failover for Scope1 and Scope2.

Scenario:
You are a network administrator for a company named Contoso,Ltd. The network is configured as shown in the exhibit.

You install the Remote Access server role on Server2.
Server2 has the following configured.
*Network address translation (NAT)
*The DHCP Server server role
The Security Policy of Contoso states that only TCP ports 80 and 443 are allowed from the internet to server2 You identify the following requirements:
* Add 28 devices to subnet2 for a temporary project.
* Configure Server2 to accept VPN connections from the internet.
* Ensure that devices on Subnet2 obtain TCP/IP settings from DHCP on Server2.
End of Scenario:
You need to identify which subnet mask you must use for subnet2. The solution must minimize the number of available IP addresses on Subnet2.
What subnet mask should you identify? To answer, select the appropriate options in the answer area.

Correct Answer: