FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. MikroTik Certification
  3. MTCNA Exam
  4. MikroTik.MTCNA.v2025-06-23.q150 Dumps
  • ««
  • «
  • …
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • …
  • »
  • »»
Download Now

Question 81

The network address is

Correct Answer: B
insert code

Question 82

If ARP=reply-only is configured on an interface, tcarmehis interface will

Correct Answer: A
insert code

Question 83

There are two routes in the routing table:
0 dst-addr=10.1.1.0/24 gateway=5.5.5.5
1 dst-addr=10.1.1.4/30 gateway=5.6.6.6
Which gateway will be used to get to the IP address 10.1.1.6?

Correct Answer: A
insert code

Question 84

Bridging loops can be avoided by enabling:

Correct Answer: A,B
Bridging loops occur when there are multiple active paths between switches or bridge interfaces, causing broadcast storms or MAC table instability. MikroTik RouterOS supports both STP (Spanning Tree Protocol) and RSTP (Rapid Spanning Tree Protocol) to detect and block redundant paths.
* A.#RSTP - Faster and preferred protocol to prevent loops.
* B.#STP - The original protocol, slower convergence but still effective.
* C.#Connection tracking - Not related to Layer 2 loop prevention.
* D.#UDP filter - Filters specific traffic types, doesn't handle loops.
* E.#ICMP filter - Not relevant to Layer 2 loop protection.
Extract from Official MTCNA Course Material - Bridging and STP:
"STP or RSTP must be enabled to prevent bridging loops. RSTP is the recommended version due to faster convergence." Extract from Rene Meneses MTCNA Study Guide - Bridging:
"Always enable STP or RSTP when using bridges with multiple paths to prevent Layer 2 loops." Extract from MikroTik Wiki - STP / RSTP:
"STP and RSTP are loop prevention mechanisms for bridges. They dynamically block redundant links."
insert code

Question 85

Which of the following Route statuses are possible?

Correct Answer: A,B,C
In the MikroTik routing table, route status flags describe the type and status of each route:
* A = Active # The route is being used to forward packets#
* C = Connected # The route is to a directly connected subnet#
* S = Static # The route was added manually by the administrator#
* D = Drop ##There is no such routing flag; "drop" may be an action in firewall or route rules but not a route status Correct route flags in MikroTik include:
* D = Dynamic
* A = Active
* C = Connected
* S = Static
* r = RIP
* o = OSPF
* b = BGP
MTCNA Routing Section - Route Flags Overview:
"Static routes show as S, connected routes as C, and routes in use are marked with A." Rene Meneses Guide - Routing Table Flags:
"Check route flags: A (Active), C (Connected), S (Static). Drop is not a valid route flag." Terry Combs Notes - Route Status Flags:
"Drop = firewall action, not route flag. Don't confuse it with routing status."
insert code
  • ««
  • «
  • …
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download MikroTik.MTCNA.v2025-06-23.q150 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.