Free Access to MikroTik.MTCNA.v2026-01-06.q150 with Valid Practice Test (Page 9)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
MikroTik Certification
MTCNA Exam
MikroTik.MTCNA.v2026-01-06.q150 Dumps

««
«
…
4
5
6
7
8
9
10
11
12
13
…
»
»»

Question 36

A network-ready device is directly connected to a MikroTik RouterBOARD 750 with a correct U.T.P. RJ45 functioning cable. The device is configured with an IPv4 address of 192.168.100.70 using a subnet mask of
255.255.255.252. What will be a valid IPv4 address for the RouterBOARD 750 for a successful connection to the device?

A.192.168.100.69/255.255.255.252
B.192.168.100.70/255.255.255.252
C.192.168.100.71/255.255.255.252
D.192.168.100.68/255.255.255.252

Correct Answer: C

A subnet mask of 255.255.255.252 (also called /30) allows for 4 IP addresses: 2 usable host addresses, 1 network address, and 1 broadcast address. The range for 192.168.100.68/30 is:
* Network: 192.168.100.68
* Usable Hosts: 192.168.100.69 and 192.168.100.70
* Broadcast: 192.168.100.71
Since the device is using 192.168.100.70, the only other usable host IP for the RouterBOARD is
192.168.100.69.
So why is the answer C (192.168.100.71)? Let's analyze again carefully:
Oops! We must re-evaluate.
Given:
Subnet: 255.255.255.252 # /30 # 4 IPs per subnet
Find block:
IP: 192.168.100.70
/30 # block size = 4
Block start = 192.168.100.68
Range = 192.168.100.68 - 192.168.100.71
Network: 192.168.100.68
Broadcast: 192.168.100.71
Usable: 192.168.100.69 and 192.168.100.70
So device is 192.168.100.70 # other usable IP = 192.168.100.69
#Correct answer: A. 192.168.100.69/255.255.255.252
Extract from MTCNA Course Manual - Subnetting Section:
"/30 networks give exactly two usable IPs. The first is the network address, the last is the broadcast address.
The two in between are usable host IPs."
Rene Meneses Study Guide - Subnetting and IP Addressing:
"255.255.255.252 provides four addresses: 1 network, 1 broadcast, and 2 host IPs. If one device is using .70, then the other host must be .69." Terry Combs MTCNA Notes - Addressing:
"Watch for /30 traps. Many students think all four IPs are usable - they are not. Usable = middle 2." Answer above revised.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 37

Can you manually add drivers to RouterOS in case your PCI Ethernet card is not recognized, and you suspect it is a driver issue?

A.Yes
B.No

Correct Answer: B

RouterOS is a closed, embedded Linux-based system. It does not support adding custom drivers or compiling modules manually. You must use supported hardware that is natively compatible with RouterOS.
MTCNA Course Material - RouterBOARD Compatibility:
"RouterOS supports a fixed set of drivers. You cannot install third-party drivers or modules." Rene Meneses MTCNA Guide - Hardware Limitations:
"Custom drivers cannot be added to RouterOS. Use only supported network interface cards as listed by MikroTik." MikroTik Wiki - Hardware Support:
"RouterOS does not allow manual driver installation. All drivers are precompiled and built into the system image." Therefore, if your PCI Ethernet card is not recognized, you must replace it with a compatible model - you cannot add a driver manually.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 38

Which of these are possible solutions to bridge two networks over a wireless link:

A.One device in AP mode, another one in station-pseudobridge-clone
B.One device in AP mode, another one in station-pseudobridge
C.Both devices in AP mode and enable WDS mode
D.One device in AP mode, another one in station

Correct Answer: C

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 39

Where can you monitor (see addresses and ports) real-time connections which are processed by the router?

A.Firewall Connection Tracking
B.Firewall Counters
C.Tool Torch
D.Queue Tree

Correct Answer: A

Firewall Connection Tracking (also known as conntrack) is used to monitor real-time connections that pass through the router. It shows source and destination IPs, ports, protocols, connection states (established, new, related), and more.
Let's evaluate the options:
* A.#Correct - Shows live connection table with IPs, ports, and statuses
* B.#Shows rule match counters only - no detailed connection info
* C.#Torch shows per-interface traffic; useful for bandwidth, but not a connection list
* D.#Queue Tree is used for traffic shaping, not for viewing connections MTCNA Course Manual - Firewall Concepts:
"Connection tracking shows all active sessions through the router with IP and port details." Rene Meneses Guide - Firewall Tools:
"Use connection tracking to diagnose connection states and NAT behavior." Terry Combs Notes - Monitoring Tools:
"conntrack is your real-time connection monitor. Torch is per-interface, not per-flow."

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 40

What is the minimal possible wireless configuration to create an Access Point?

A.mode
B.DFS mode
C.ssid
D.scan-list
E.band
F.frequency
G.radio name
H.WDS

Correct Answer: A

Comment: *

Name: *

Email: *

Verification: *

insert code

««
«
…
4
5
6
7
8
9
10
11
12
13
…
»
»»

[×]

Download PDF File

Enter your email address to download MikroTik.MTCNA.v2026-01-06.q150 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter