Free Network Appliance NS0-506 Exam Dumps Questions & Answers

On a FAS8040, which port is used for FCoE connections?

• A.  e0P
• B.  0a
• C.  e0M
• D.  e0h

Click the Exhibit button.
You have a 2-node data ONTAP 8.3 cluster.
Based on the exhibit, which change must be made to make svm1 conform to iSCSI best practices?
cl01::> net int show -vserver
svm1 -data -protocol iscsi
Logical Status Network
Current Current Is
Vserver Interface Admin/Oper
Address/Mask Node Port Home
----------- ---------- ------
---- ------------------ -----
-------- ------- ----
svm1
up/up 10.204.34.25/24 cl01-01
a0a 434 true
cl01::>iscsi show -vserver
svm1
Vserver: svm1
Target Name: iqn.1992 -
08.com.netapp: sn.ca5eaa069c211
Target Alias: svm1
Administrative Status: up

• A.  An iSCSI LIF must be added to node cl01-02.
• B.  The Target Alias must be modified to match the Target Name.
• C.  The iSCSI LIFs must be moved to a VLAN higher than 1024.
• D.  The iSCSI LIFs must be moved to a physical interface; iSCSI LIFs are not supported on top of an ifgrp.

Click the Exhibit button.
A storage administrator has the configuration shown in the exhibit.
In which scenario would a volume move be successful?
cl01::>vserver show -vserver
svm1
Vserver: svm1
Vserver Type: data
Vserver UUID: 1630b8eb-c2a6-
11e4-a7dd-123478563865
Root Volume: svm1_root
Aggregate: Node1_aggr1,
Node2_aggr1
Name Service Switch: file,
nis
Allowed Protocols: fcp
Disallowed Protocols: nfs,
cifs, iscsi, ndmp
Is Vserver with Infinite
Volume: false
QoS Policy Group: -
cl01::>vserver show -vserver
svm2
Vserver Type: data
Vserver UUID: 1630b8eb-c2a6-
11e4-a7dd-123478563412
Root Volume: svm2_root
Aggregate: Node1_aggr1,
Node2_aggr1, Node1_aggr2
Name Service Switch: file,
nis
Allowed Protocols: fcp
Disallowed Protocols: nfs,
cifs, iscsi, ndmp
Is Vserver with Infinite
Volume: false
QoS Policy Group: -
cl01::>

• A.  from svm2 aggregate Node1_aggr1 to svm2 aggregate Node1_aggr2
• B.  from svm1 aggregate Node1_aggr1 to svm1 aggregate Node2_aggr1
• C.  from svm1 aggregate Node1_aggr1 to svm2 aggregate Node1_aggr2
• D.  from svm1 aggregate Node1_aggr1 to svm1 aggregate Node1_aggr2

A new server has been installed in your environment, but it is unable to see its NetApp boot LUN. You have narrowed
the problem down to the zoning on your Cisco switch which has the following configuration:
zone name z_NetAppvsan 400
memberpwwn 20:00:00:25:b5:c0:ff:ee
memberpwwn 50:0a:09:84:8d:7c:51:d5
zoneset name zs_NetAppvsan 400
memberz_NetApp
zoneset activate name zs_NetAppvsan 400
What is the problem with your zoning configuration?

• A.  The member does not reference the VSAN.
• B.  The PWWN for your NetApp LIF is incorrect.
• C.  The zoneset was improperly activated.
• D.  The zone and zoneset names do not match.

Which information-gathering command should you use to gather logs for troubleshooting switch information for your
Brocade switches?

• A.  cfgshow
• B.  supportsave
• C.  fabricshow
• D.  configshow