Free Access to Cisco.300-410.v2024-04-03.q275 with Valid Practice Test (Page 4)

Question 11

Refer to the exhibit.

An engineer is troubleshooting a TACACS problem.
Which action resolves the issue?

A.Configure a matching TACACS server IP.
B.Configure a matching preshared key.
C.Generate authentication from a relative source interface.
D.Apply a configured AAA profile to the VTY.

Question 12

Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?

A.Replace the capital "C" with a lowercase "c" in the aaa authentication login Console local command.
B.Add the login authentication Console command to the line configuration
C.Add the aaa authentication login default none command to the global configuration.
D.Add the aaa authentication login default group tacacs+ local-case command to the global configuration.

Question 13

Drag and drop the DHCP messages from the left onto the correct uses on the right.

Correct Answer:

Explanation

DHCPACK
The server-to-client communication with configuration parameters, including committed network address.
DHCPINFORM
The client-to-server communication, asking for only local configuration parameters that the client already has externally configured as an address.
DHCPNAK
The server-to-client communication, refusing the request for configuration parameter.
DHCPDECLINE
The client-to-server communication, indicating that the network address is already in use Reference:
https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html DHCPINFORM: If a client has obtained a network address through some other means or has a manually configured IP address, a client workstation may use a DHCPINFORM request message to obtain other local configuration parameters, such as the domain name and Domain Name Servers (DNSs). DHCP servers receiving a DHCPINFORM message construct a DHCPACK message with any local configuration parameters appropriate for the client without allocating a new IP address. This DHCPACK will be sent unicast to the client.
DHCPNAK: If the selected server is unable to satisfy the DHCPREQUEST message, the DHCP server will respond with a DHCPNAK message. When the client receives a DHCPNAK message, or does not receive a response to a DHCPREQUEST message, the client restarts the configuration process by going into the Requesting state. The client will retransmit the DHCPREQUEST at least four times within 60 seconds before restarting the Initializing state.
DHCPACK: After the DHCP server receives the DHCPREQUEST, it acknowledges the request with a DHCPACK message, thus completing the initialization process.
DHCPDECLINE: The client receives the DHCPACK and will optionally perform a final check on the parameters. The client performs this procedure by sending Address Resolution Protocol (ARP) requests for the IP address provided in the DHCPACK. If the client detects that the address is already in use by receiving a reply to the ARP request, the client will send a DHCPDECLINE message to the server and restart the configuration process by going into the Requesting state.
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html

Question 14

Refer to the exhibit.

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

A.Use an extended access list instead of a standard access list.
B.Use a prefix list instead of an access list in the route map.
C.Change sequence 10 in the route-map command from permit to deny.
D.Add this statement to the route map: route-map RM-OSPF-DL deny 20.

Question 15

Drag and drop the LDP features from the left onto the descriptions on the right

Question 11

Question 12

Question 13

Question 14

Question 15

Download PDF File