Refer to the exhibit.

A network engineer is setting up a multihomed OTV network. The first site has been set up with a primary and secondary adjacency server. Which configuration must be added on the remote OTV AEDs site?

• A.interface Overlay200
  otv join-interface Ethernet1/2
  otv extend-vlan 178, 2500-2563
  otv use-adjacency-server 20.1.1.1 20.2.1.1 unicast-only
• B.interface Overlay200
  otv join-interface Ethernet1/2
  otv extend-vlan 178, 2500-2563
• C.interface Overlay200
  otv join-interface Ethernet1/2
  otv extend-vlan 178, 2500-2563
  otv use-adjacency-server 20.1.1.1 unicast-only
• D.interface Overlay200
  otv join-interface Ethernet1/2
  otv extand-vlan 178, 2500-2563
  otv adjacency-server unicast-only

Comment: *

Name: *

Email: *

Verification: *

Which statement about the MAC address that the FCoE Initialization Protocol chooses for use by an E-Node in an FCoE implementation is true?

• A.The FCoE Initialization Protocol uses a 24-bit FC-MAP and concatenates a 24-bit Fibre Channel ID to create a fabric-provided MAC address.
• B.The FCoE Initialization Protocol uses the burned-in MAC address of the converged network adapter for all FCoE operations.
• C.FCoE does not use a MAC address. The FCoE Initialization Protocol is used to acquire a Fibre Channel ID, and the address is used for all FCoE communications in the same way as Fibre Channel Protocol.
• D.The FCoE Initialization Protocol uses 01.00.0C as the first 24 bits of the MAC address and appends a 24-bit Fibre Channel ID to derive a full 48-bit FCoE MAC address.

Correct Answer: A

FCoE uses a Fabric Provided MAC Address (FPMA) for SAN traffic. The ENode still gets a 24-bit FCID. FPMA is built by concatenating a 24-bit FCoE MAC address prefix (FC-MAP), ranging from
0x0E-FC-00 to 0x0E-FC-FF, to the 24-bit FCID, as shown in Figure 8-13.
Being able to build a unique MAC address for the ENode directly from its FCID saves the switch from having to maintain a table that associates FCID and MAC addresses.

Comment: *

Name: *

Email: *

Verification: *

An engineer must perform backup and restore of the Cisco UCS Manager configuration. The configuration must be stored on a remote server via XML encoding. The backup must store the configurations of the chassis.
FEX, rack servers. lOMs, and blade server. Which set of actions accomplishes these goals?

• A.Perform a system configuration backup and run the merge import method
• B.Perform a logical configuration backup and run the replace import method.
• C.Perform a ful state configuration backup and run the restore procedure.
• D.Perform an all configuration backup and run the system restore procedure.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

An engineer must monitor all LAN traffic on Fabric A from a blade server. Which source should be configured in the test-span monitor session to complete this task?

• A.all vHBAs from the service profile that correspond to this server
• B.all uplink FCoE ports
• C.all uplink Ethernet ports
• D.all vNICs from the service profile that correspond to this server

Correct Answer: D

Explanation
https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration

Comment: *

Name: *

Email: *

Verification: *

A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted. Which set of steps must be taken to meet these requirements?

• A.1 Perform a running-config backup to an SCP server
  2 Copy running-config in the boot flash to the running-config file
• B.1 Perform a running-config backup to an SFTP server
  2 Copy backup-config from the SFTP server to the running-config file
• C.1 Perform a startup-config backup to an FTP server.
  2 Copy startup-config in the boot flash to the running-config file
• D.1 Perform a startup-config backup to a TFTP server
  2 Copy backup-config from the backup server to the running-config file

Comment: *

Name: *

Email: *

Verification: *