FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. CompTIA Certification
  3. N10-008 Exam
  4. CompTIA.N10-008.v2025-06-03.q684 Dumps
  • ««
  • «
  • …
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • …
  • »
  • »»
Download Now

Question 81

A network administrator is configuring a load balancer for two systems. Which of the following must the administrator configure to ensure connectivity during a failover?

Correct Answer: A
You can use a virtual IP to achieve load balancing across multiple interfaces.
insert code

Question 82

A technician is investigating an intermittent connectivity issue that occurs when specific WAPs are turned on.
The technician checks into the issue further and finds the WAPs that are having issues share channel five.
Which of the following is most likely causing the issue?

Correct Answer: B
The most likely cause of the intermittent connectivity issues when specific Wireless Access Points (WAPs) are turned on and share channel five is interference. Wireless interference occurs when multiple devices operate on the same channel within close proximity to each other, leading to signal congestion and reduced performance. This type of interference can cause the connectivity to be sporadic, as described. Other options like polarization, incorrect channel (since they are on the intended channel), or low power levels would generally not cause intermittent issues strictly when WAPs are turned on.
insert code

Question 83

Which of the following describes the BEST device to configure as a DHCP relay?

Correct Answer: D
insert code

Question 84

A WAN technician reviews activity and identifies newly installed hardware that is causing outages over an eight-hour period. Which of the following should be considered FIRST?

Correct Answer: D
The most likely cause of outages due to newly installed hardware is a misconfiguration of the device settings.
Therefore, the first step should be to review the device configuration and check for any errors or inconsistencies that might affect the WAN connectivity.
References: Network+ Study Guide Objective 2.1: Explain the importance of network documentation.
insert code

Question 85

Users are connected to a switch on an Ethernet interface of a campus router. The service provider is connected to the serial 1 interface on the router. The output of the interfaces is:
E1/0: 192.168.8.1/24
S1: 192.168.7.252/30
After router and device configurations are applied, internet access is not possible. Which of the following is the most likely cause?

Correct Answer: C
The default gateway is the IP address of the router that connects a network to the internet or another network.
The default gateway is usually configured on the devices that need to access the internet or other networks, such as PCs, servers, or routers. If the router was configured with an incorrect default gateway, it would not be able to forward packets to the correct destination, and internet access would not be possible.
The other options are not the most likely causes of the issue. The Ethernet interface is the physical port that connects a device to a network using a cable. If the Ethernet interface was configured with an incorrect IP address, it would cause a problem with the local network connectivity, not the internet access. The loopback address is a special IP address that refers to the device itself, usually used for testing or troubleshooting purposes. If the router was configured with an incorrect loopback address, it would not affect the internet access, as the loopback address is not used for routing packets to other networks. The serial interface is another type of physical port that connects a device to a network using a serial cable, often used for WAN connections. If the serial interface was configured with the incorrect subnet mask, it would cause a problem with the WAN connectivity, not the internet access, as the subnet mask is used to determine the network and host portions of an IP address.
ReferencesWhat is a Default Gateway? | HowStuffWorksWhat is an Ethernet Interface? - Definition from TechopediaWhat is a Loopback Address? - Definition from TechopediaWhat is a Serial Interface? - Definition from Techopedia
insert code
  • ««
  • «
  • …
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download CompTIA.N10-008.v2025-06-03.q684 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.