A customer needs a networking solution that supports their Microsoft Skype for Business Unified
Communications (UC) solution. The architect plans to use multiple Aruba APs, switches, and controllers.
The customer wants real time statistics and assessment of call quality. Which component should the architect
include to provide these services?

• A.Aruba Central
• B.Aruba ClearPass
• C.Aruba Mobility Master (MM)
• D.Aruba AirWare

Comment: *

Name: *

Email: *

Verification: *

A Remote AP provisioned in "Split-Tunnel" Forwarding mode has which characteristic?

• A.The user role must have a "Permit" statement in order to locally bridge the traffic.
• B.Local traffic first goes to the controller and is then spilt back to the local network.
• C.The RAP uses PAPI to send data traffic to the controller.
• D.The user role must have a "route dst-nat" statement to locally bridge the traffic.
• E.Traffic is IPSec encrypted before it is sent to the controller.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

What is one reason for an architect to recommend the use of Virtual Switching Framework (VSF) in this network?

• A.VSF enables administrators to manage all 18 switches as a single switch.
• B.VSF transforms switches into virtual extensions of the MCs to simplify MST management.
• C.VSF enables software-defined network monitoring in conjunction with AirWare.
• D.VSF simplifies the topology and eliminates the need for spanning tree.

Comment: *

Name: *

Email: *

Verification: *

Read this scenario thoroughly, and then answer each question that displays on the right side of the screen.
An architect proposes these products for a customer who wants a wireless and wired upgrade:
1. Aruba 2930M switches at the access layer
2. Aruba 5406R switches at the core
3. Aruba AP-325s
4. Aruba 7205 Mobility Controllers (MCs), deployed in a cluster
5. Aruba Mobility Master (MM)
6. Aruba ClearPass Cx000V
7. Aruba AirWare
The architect also needs to propose a security plan for the solution. The customer has 900 employees and up to 30 guests a day. The customer wants to protect the internal perimeter of the network with authentication and simple access controls. The customer is most concerned about wireless security, but also wants to ensure that only trusted users connect on the wire. However, the customer also wants all wired traffic to be forwarded locally on access layer switches. The customer already has a third-party firewall that protects the data center.
The customer wants to use certificates to authenticate user devices, but is concerned about the complexity of deploying the solution. The architect should recommend a way to simplify. For the most part users connect company-issued laptops to the network. However, users can bring their own devices and connect them to the network. The customer does not know how many devices each user will connect, but expects about two or three per-user. DHCP logs indicate that the network supports a maximum of 2800 devices.
Refer to the provided scenario. Based on the plan for wired authentication, what is a correct plan for wired user VLANs?

• A.configure the same roles on switches and MCs to place wired and wireless users in the same VLANs.
  Extend VLANs from access layer switches to the core.
• B.specify the VLANs in network policies on AirWare, and ensure that both the switches and MCs are managed by AirWare
• C.assign wired users to different VLANs from wireless users, based on port or role assignments on access layer switches. Extend the VLANs to the core.
• D.use the MCs to assign wired users to their VLANs, and extend the VLANs to a Layer 3 switch connected to the MC

Comment: *

Name: *

Email: *

Verification: *

An architect proposes an Aruba solution with a hardware Mobility Master (MM) to a customer. The customer has a disaster recovery site which is connected to the main site at Layer 3. The customer requires the MM to remain available in case of a total site failure.
Which plan meets the customer requirements?

• A.Deploy a hardware MM to the disaster recovery site and set its IP address as the standby master for MCs.
• B.Deploy the virtual MM (VMM) to the disaster recovery site and set the VMM IP address to the same address as the hardware MM.
• C.Deploy the virtual MM (VMM) to the disaster recovery site and configure clustering on the hardware and software appliances.
• D.Deploy a hardware MM to the disaster recovery site and set up VRRP between them.

Comment: *

Name: *

Email: *

Verification: *