Free Access to HP.HPE6-A85.v2024-05-10.q58 with Valid Practice Test (Page 6)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
HP Certification
HPE6-A85 Exam
HP.HPE6-A85.v2024-05-10.q58 Dumps

«
1
2
3
4
5
6
7
8
9
10
…
»
»»

Question 21

When using the network check page in Central, what kind of tests can you run on switches? (Select two.)

A.Speed test (iperf)
B.Ping test
C.A full hardware check, including a heavy memory check
D.LED-check.
E.PoE-check

Correct Answer: B,E

In Aruba Central's network check page, you can run several diagnostic tests on switches. A ping test is a common utility to check the reachability of a host on an IP network. A Power over Ethernet (PoE) check can help verify the power delivery status to PoE-capable devices. These tests are crucial for ensuring connectivity and power supply to network devices

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 22

What is indicated by a solid amber radio status LED on an Aruba AP?

A.Not enough PoE is provided from the switch to power both radios of the AP
B.The radio is working in mesh mode
C.The radio is working the 5 GHz band only.
D.The radio is enabled in monitor or spectrum analysis mode

Correct Answer: A

A solid amber radio status LED on an Aruba Access Point (AP) typically indicates a power issue, specifically that not enough Power over Ethernet (PoE) is being provided from the switch to fully power all functionalities of the AP, including both of its radios. In environments where APs are powered via PoE, it is crucial to ensure that the switch supplying the power is capable of delivering sufficient power for the AP's requirements. If the AP does not receive enough power, it may disable certain features or radios to conserve energy, which is indicated by the solid amber LED. This situation is common in scenarios where the switch provides only 802.3af PoE rather than the more powerful 802.3at PoE+ needed by some high-performance APs to operate all features, including dual radios, at full capacity.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 23

What is the recommended UXI monitoring solution in large logistic facilities?

A.Use a special ruggedized UXI sensor.
B.Use the UXI App on all handheld devices running on Windows CE.
C.Add a UXI sensor in every aisle of the logistic space.
D.Use the UXI App direct on Zebra scanning devices running on Android.

Correct Answer: C

In large logistic facilities, to ensure comprehensive monitoring and performance analysis, it's recommended to place a User Experience Insight (UXI) sensor in every aisle. This allows for detailed and specific monitoring of network performance across the extensive coverage area of such facilities.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 24

When would you bond multiple 20MHz wide 802.11 channels?

A.To decrease the Signal to Noise Ratio (SNR)
B.To increase throughput between the client and AP
C.To provision highly available AP groups
D.To utilize high gain omni-directional antennas

Correct Answer: B

Bonding multiple 20MHz wide 802.11 channels is a technique to create a wider bandwidth channel that supports higher data rate transmissions. It can increase the throughput between the client and AP by using more spectrum resources and reducing interference. Reference: https://ieeexplore.ieee.org/document/9288995 Bonding multiple 20MHz wide 802.11 channels is a technique used to increase the throughput between the client device and the Access Point (AP). By combining two or more 20MHz channels into a wider channel (e.g., 40MHz, 80MHz, or even 160MHz), the data carrying capacity and, consequently, the overall throughput of the wireless connection are increased. This method is particularly useful in high-bandwidth applications or environments where higher data rates are required.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 25

When would you bond multiple 20MHz wide 802.11 channels?

A.To decrease the Signal to Noise Ratio (SNR)
B.To increase throughput between the client and AP
C.To provision highly available AP groups
D.To utilize high gain omni-directional antennas

Correct Answer: B

Explanation
Bonding multiple 20MHz wide 802.11 channels is a technique to create a wider bandwidth channel that supports higher data rate transmissions. It can increase the throughput between the client and AP by using more spectrum resources and reducing interference. References:https://ieeexplore.ieee.org/document/9288995

Comment: *

Name: *

Email: *

Verification: *

insert code

«
1
2
3
4
5
6
7
8
9
10
…
»
»»

[×]

Download PDF File

Enter your email address to download HP.HPE6-A85.v2024-05-10.q58 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter