Free Access to HP.HPE6-A85.v2025-02-08.q90 with Valid Practice Test (Page 18)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
HP Certification
HPE6-A85 Exam
HP.HPE6-A85.v2025-02-08.q90 Dumps

««
«
…
10
11
12
13
14
15
16
17
18
19
»

Question 81

When would you bond multiple 20MHz wide 802.11 channels?

A.To decrease the Signal to Noise Ratio (SNR)
B.To increase throughput between the client and AP
C.To provision highly available AP groups
D.To utilize high gain omni-directional antennas

Correct Answer: B

Bonding multiple 20MHz wide 802.11 channels is a technique to create a wider bandwidth channel that supports higher data rate transmissions. It can increase the throughput between the client and AP by using more spectrum resources and reducing interference.
References: https://ieeexplore.ieee.org/document/9288995

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 82

What is an advantage of using Layer 2 MAC authentication?

A.it matches user names to MAC address
B.No setup is required on the client
C.MAC allow lists are easily maintained over time
D.MAC identifiers are hard to spoof

Correct Answer: B

Layer 2 MAC authentication is a method of authenticating devices based on their MAC addresses without requiring any client-side configuration or credentials. The switch sends the MAC address of the device to an authentication server such as ClearPass or RADIUS, which checks if the MAC address is authorized to access the network. If yes, the switch grants access to the device based on the assigned role and policies. If no, the switch denies access or redirects the device to a captive portal for further authentication. Reference: https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/1-overview/mac-authentication.htm

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 83

Which commands are used to set a default route to 10.4.5.1 on an Aruba CX switch when ln-band management using an SVl is being used?

A.iP default-gateway 10.4.5.1
B.ip route 0 0 0.070 10.4 5.1 vrf mgmt
C.ip route 0.0 0 0/0 10.4.5.1
D.default-gateway 10.4.5.1

Correct Answer: C

The command that is used to set a default route to 10.4.5.1 on an Aruba CX switch when in-band management using an SVI is being used is ip route 0.0 0 0/0 10.4.5.1 . This command specifies the destination network address (0.0 0 0) and prefix length (/0) and the next-hop address (10.4.5.1) for reaching any network that is not directly connected to the switch. The default route applies to the default VRF Virtual Routing and Forwarding. VRF is a technology that allows multiple instances of a routing table to co-exist within the same router at the same time. VRFs are typically used to segment network traffic for security, privacy, or administrative purposes. , which is used for in-band management traffic that goes through an SVI Switch Virtual Interface. SVI is a virtual interface on a switch that allows the switch to route packets between different VLANs on the same switch or different switches that are connected by a trunk link. An SVI is associated with a VLAN and has an IP address and subnet mask assigned to it12. Reference: 1 https://www.arubanetworks.com/techdocs/AOS-CX/10_08/HTML/ip_route_4100i-6000-6100-6200/Content/Chp_StatRoute/def-rou.htm 2 https://www.arubanetworks.com/techdocs/AOS-CX/10_08/HTML/ip_route_4100i-6000-6100-6200/Content/Chp_VRF/vrf-overview.htm

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 84

When using an Aruba standalone AP you select "Native VLAN" for the Client VLAN Assignment In which subnet will the client IPs reside?

A.The same subnet as the mobility controller
B.The same subnet as the Aruba ESP gateway
C.The same subnet as the mobility conductor
D.The same subnet as the access point

Correct Answer: D

When using an Aruba standalone AP, selecting "Native VLAN" for the Client VLAN Assignment means that the clients will get their IP addresses from the same subnet as the access point's IP address. This is because the access point acts as a DHCP server for the clients in this mode. Reference: https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/iap-dhcp/iap-dhcp.htm

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 85

What does a slow amber-flashing Stack-LED indicate?

A.One switch has a stacking failure.
B.A port has a stacking failure Stacking mode Is not selected
C.Stacking mode selected
D.Stacking is synchronizing Please wait

Correct Answer: C

A slow amber-flashing Stack-LED indicates that stacking mode is selected on the switch. This means that the switch is ready to join a stack or form a new stack if no other switches are present. Reference: https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/1-overview/stacking-leds.htm

Comment: *

Name: *

Email: *

Verification: *

insert code

««
«
…
10
11
12
13
14
15
16
17
18
19
»

[×]

Download PDF File

Enter your email address to download HP.HPE6-A85.v2025-02-08.q90 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter