An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

• A.F-Series module
• B.M-Series module
• C.STORAGE-ENT license
• D.ESSENTIALS license
• E.FCoE license

Comment: *

Name: *

Email: *

Verification: *

Refer to an exhibit.

An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

• A.Reload the same system image.
• B.Load a new system image.
• C.Use the same system image as the kickstart image.
• D.Save the system image in NVRAM.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?

• A.Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.
• B.Set the local group number as 300 in the remote data center configuration
• C.Run version 1 and version 2 HSRP on VLAN300 in the local data center.
• D.Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

Correct Answer: A

Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp_fhrp/configuration/xe-16/fhp-xe-16-book/fhp-hsrp-v2.p

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

• A.switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
• B.switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
• C.switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
• D.switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

Comment: *

Name: *

Email: *

Verification: *

During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a "No Signal" message from the vKVM and physical connection. Which set of steps resolves the issue?

• A.1- Disconnect the power cord
  2- Confirm that all cards are property seated
  3- Connect the power cord and power on the server
• B.1- Power off the server and disconnect the power cord
  2- Confirm that all cards are property seated
  3- Connect the power cord and power on the server
• C.1- Power off the server and disconnect the power cord
  2- Confirm that all cards are available
  3- Connect the power cord and power on the server
• D.1- Disconnect the power cord
  2- Confirm that all cards are properly seated
  3- Connect the power cord

Correct Answer: B

Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/ts/guide/b_C-Series_Troubleshooting_Guide.pd

Comment: *

Name: *

Email: *

Verification: *