Refer to the exhibit.

A Cisco UCS Fabric Interconnect fails during the upgrade process. The working images of the fabric interconnect are stored on the bootflash. Which set of commands recovers the fabric interconnect?

• A.loader> dir
  loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
  switch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.bin switch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin
• B.loader> dir
  loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
  switch(boot)# init system
  switch(boot)# reload
  switch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin
• C.loader> dir
  loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
  switch(boot)# init system
  switch(boot)# reload
  switch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin
• D.loader> dir
  loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin
  switch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.bin switch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

Comment: *

Name: *

Email: *

Verification: *

Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.

Correct Answer:

Comment: *

Name: *

Email: *

Verification: *

A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

• A.1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
  2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
  3) Check for runtime link down status
  4) Reseat the affected IOM.
• B.1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
  2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
  3) Check for runtime link down status
  4) Reseat the affected IOM.
• C.1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
  2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
  3) Check for runtime link down status.
  4) Reseat the affected IOM.
• D.1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
  2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
  3) Check for runtime link down status.
  4) Reseat the affected IOM.

Correct Answer: B

Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/UCSTroubleshooti

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

An engineer deploys SAN environment with two interconnected Cisco MDS 9000 Series switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit. Which action resolves the issue?

• A.Import or export a zone set between the switches to synchronize the switches.
• B.Change the name of one of the zones to match the other zone set.
• C.Set the distribute policy of the zone to full.
• D.Ensure that the zone members have different names.

Correct Answer: A

Explanation
https://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_3_x/troubleshooting/guide/ts_guide.pd

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit. A PC belongs to VLAN 68. The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?

• A.Replace HSRP with GLBP.
• B.Remove the HSRP configuration.
• C.Enable the peer-gateway feature.
• D.Configure ip arp synchronization on both switches.

Comment: *

Name: *

Email: *

Verification: *