Free Access to NetworkAppliance.NS0-593.v2024-04-29.q44 with Valid Practice Test (Page 5)

Question 16

You are trying to deploy a Connector in the AWScloud from NetApp Cloud Manager. The deployment fails
and shows the message 'Insufficient permissions to deploy Cloud Connector". You have verified the AWS
access key and the AWS secret key.
In this scenario, what Is the reason that the deployment failed?

A.The required Identity and Access Management (IAM) policies were not Installed.
B.The user lacks the permission to deploy within Cloud Manager.
C.No AWS Marketplace subscription is associated with Cloud Manager.
D.The Connector can be deployed only inAWS GovCloud (US).

Question 17

You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show
command for more Information. You notice the "Urge" column has non-zero values.
In this scenario, which statement is true?

A.The data placement is uneven.
B.The constituent volumes are out ofInodes.
C.The constituent volumes are completely full.
D.The aggregate is completely full.

Question 18

Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP for Azure HA solution is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why. No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.
In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is working properly? {Choose two.)

A.-mail-hosts
B.-transport
C.-proxy-url
D.-to

Question 19

After a motherboard replacement on a NetApp AFF A300 in a SAN environment, the customer states that ports 0e and 0f are unable to connect to the fabric. The ports report "offline".
What would you examine first to troubleshoot the issue?

A.vserver fcp wwpn-alias show command output
B.system node hardware unified-connect show command output
C.storage port show command output
D.vserver fcp interface show command output

Correct Answer: B

Here is my reasoning:
The system node hardware unified-connect show command displays the status and configuration of the Unified Connect ports on a node1. This command can help you identify if the ports are configured correctly and if they have any errors or faults.
The ports 0e and 0f on the AFF A300 are 10GbE ports that support both Ethernet and Fibre Channel over Ethernet (FCoE) protocols2. These ports are part of the Unified Connect feature, which enables you to use the same physical port for different protocols without requiring additional hardware3.
If the ports are offline, it could indicate a problem with the port configuration, the cable connection, the switch configuration, or the protocol settings. The system node hardware unified-connect show command can help you troubleshoot these issues by showing you the port mode, speed, duplex, state, and error count1.
The other commands in the options are not as helpful for troubleshooting the port issue, because they show different information that is not related to the Unified Connect feature or the port status. For example:
The vserver fcp wwpn-alias show command displays the World Wide Port Name (WWPN) aliases for the Fibre Channel Protocol (FCP) logical interfaces (LIFs) on a Vserver4. This command can help you manage the FCP LIFs, but it does not show the status of the physical ports or the Unified Connect feature.
The storage port show command displays the status and configuration of the storage ports on a node5. This command can help you manage the storage ports, but it does not show the status of the Unified Connect ports or the FCoE protocol.
The vserver fcp interface show command displays the status and configuration of the FCP LIFs on a Vserver6. This command can help you manage the FCP LIFs, but it does not show the status of the physical ports or the Unified Connect feature.
Here are some references that might help you:
1: system node hardware unified-connect show - NetApp 2: AFF A300 system installation - NetApp 3: Unified Connect - NetApp 4: vserver fcp wwpn-alias show - NetApp 5: storage port show - NetApp 6: vserver fcp interface show - NetApp

Question 20

Your customer mentions that they have accidentally destroyed both rootaggregates in their two-node cluster.
In this scenario, what are two actions that must be performed? (Choose two.)

A.Install ONTAP from a USB device.
B.Re-create the cluster from the remote backup.
C.Rejoin the second node to the re-created cluster.
D.Re-create the cluster from the local backup.

Question 16

Question 17

Question 18

Question 19

Question 20

Download PDF File