Free Access to NetworkAppliance.NS0-094.v2026-08-18.q52 with Valid Practice Test (Page 10)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
Network Appliance Certification
NS0-094 Exam
NetworkAppliance.NS0-094.v2026-08-18.q52 Dumps

««
«
…
3
4
5
6
7
8
9
10
11
12
»

Question 41

A NetApp node fails to boot and displays repeated boot-loop behavior after hardware maintenance. Which troubleshooting step should be performed FIRST?

A.Verify recently installed FRUs and cable seating
B.Destroy the root aggregate
C.Replace every disk in the shelf
D.Reset all cluster licenses

Correct Answer: A

After maintenance, improperly seated FRUs or disconnected cables are common causes of boot loops. Engineers should first validate hardware installation integrity before performing destructive actions. Replacing all disks or resetting licenses introduces unnecessary disruption and does not address likely root causes.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 42

A customer observes that one node repeatedly enters takeover mode due to thermal alarms.
Which FRU should be inspected FIRST?

A.Power cable labels
B.Cooling fans and airflow obstructions
C.Shelf serial numbers
D.Cluster passwords

Correct Answer: B

Thermal alarms are commonly associated with failed cooling fans, blocked airflow, or improper rack ventilation. Inspecting cooling-related FRUs is the highest priority. Shelf serial numbers and passwords are unrelated to thermal conditions. Continued overheating may eventually force protective node shutdowns.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 43

On a NetApp FAS9000 system, which two field replaceable units (FRUs) are supported for replacement without takeover? (Choose two.)

A.I/O module
B.DCPM module
C.caching module
D.NVRAM module

Correct Answer: A,D

FRUs on FAS9000 Supporting Replacement Without Takeover:
A). (I/O Module): I/O modules can be replaced hot (without takeover) to maintain system uptime during hardware servicing.
D). (NVRAM Module): NVRAM modules on FAS9000 can also be replaced without a node takeover, ensuring data integrity during replacement.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 44

A node has panicked with a PCI/NMI error. Giveback has not been performed. Which two commands should you run to collect the logs to determine the cause? (Choose two.)

A.pelog -a -g=2
B.show pci -v
C.rdfile /mroot/etc/log/SSRAM
D.event log show

Correct Answer: A,C

To diagnose a PCI/NMI error and collect logs, use the following commands:
1. pelog -a -g=2
What it does:
This command collects PCI error logs, including detailed information about PCI devices and the errors that caused the panic.
How to use:
Run the command from the nodeshell to capture the required PCI log entries.
2. rdfile /mroot/etc/log/SSRAM
What it does:
This command reads the SSRAM log file, which contains low-level error information related to PCI and other hardware subsystems.
How to use:
Run the command to view the log entries directly for detailed troubleshooting.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 45

Which two statements regarding drive 1.2.3.L1 are true? (Choose two.)

A.The drive is in shelf 2.
B.The drive is in bay 3.
C.The drive is in bay 2.
D.The drive is in shelf 1.

Correct Answer: A,B

The identifier 1.2.3.L1 follows the NetApp disk naming convention, which specifies the location of the drive in the system. Here is the breakdown of the identifier:
1: This indicates the stack ID or loop ID. It represents the stack number in the disk shelf configuration.
2: This indicates the shelf ID. In this case, the drive is located in shelf 2.
3: This indicates the bay ID or slot number within the shelf. The drive is in bay 3.
L1: This represents the logical port or logical disk identifier.
How to Interpret Disk Identifier 1.2.3.L1:
The shelf ID is 2, so the drive is in shelf 2 (A is correct). The bay ID is 3, so the drive is in bay 3 (B is correct).

Comment: *

Name: *

Email: *

Verification: *

insert code

««
«
…
3
4
5
6
7
8
9
10
11
12
»

[×]

Download PDF File

Enter your email address to download NetworkAppliance.NS0-094.v2026-08-18.q52 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter