FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. F5 Certification
  3. F5CAB5 Exam
  4. F5.F5CAB5.v2026-07-18.q66 Dumps
  • ««
  • «
  • …
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • »
Download Now

Question 51

During a high-demand traffic event, the BIG-IP Administrator needs to limit the number of new connections per second allowed to a Virtual Server. What should the administrator apply to accomplish this task?

Correct Answer: D
F5 BIG-IP provides two distinct ways to throttle traffic on a Virtual Server: total capacity and velocity.
Connection Rate Limit: This setting specifically controls the number of new connection attempts per second. It is the correct tool for managing traffic spikes and protecting backend resources from being overwhelmed by a high frequency of new requests.
Comparison (Connection Limit): A standard Connection Limit (Option C) restricts the total concurrent connections allowed at any one time, regardless of how fast they arrive.
Other Profiles: OneConnect (Option A) is used for connection pooling and reuse to reduce server-side load, and HTTP Compression (Option B) reduces bandwidth usage but does not limit connection counts or rates.
insert code

Question 52

A BIG-IP device sends out the following SNMP trap: big-ipo.f5.com - bigipExternalLinkChange Link: 1.0 is DOWN. Where in the BIG-IP Configuration utility should the BIG-IP Administrator verify the current status of Link 1.0?

Correct Answer: D
Comprehensive and Detailed Explanation From BIG-IP Administration Support and Troubleshooting documents:Identifying network-level performance issues often starts with investigating hardware-level alerts78. In F5 terminology, a "Link" like "1.0" or "1.1" refers to a physical interface on the appliance79.
When an SNMP trap reports that a link is "DOWN," it indicates a loss of signal or an administrative shutdown of the physical port80. To verify this, the administrator must navigate to Network > Interfaces > Interface List81. This screen provides real-time status, showing whether the interface is "up," "down," or
"uninitialized," as well as any media speed or duplex mismatches that could be causing performance degradation82. Troubleshooting this is the first step in resolving "pool member down" or "VLAN failsafe" issues, as a down interface will take down any VLANs associated with it, immediately halting all traffic flow for the services relying on that physical path.
insert code

Question 53

A gateway_icmp health monitor is configured on a pool. The BIG-IP Administrator is investigating why the pool is reported as down while the server is online. Other pools with servers in the same subnet are correctly monitored. What can cause this behavior? (Choose one answer)

Correct Answer: C
A gateway_icmp monitor checks basic network reachability by sending ICMP echo requests (pings) to the pool member or its gateway. If the pool is marked DOWN while the server is confirmed to be online, the most likely cause is that ICMP traffic is being blocked.
Ahost-based firewall active on the server (Option C)can block ICMP echo requests or replies, preventing BIG-IP from receiving a successful response to the health check. This results in the monitor failing and the pool member being marked down, even though the server and application are otherwise functioning normally. This explanation is consistent with the scenario where other servers in the same subnet work correctly, indicating that routing and BIG-IP configuration are not the issue.
insert code

Question 54

In a busy environment where a pool is not functioning as expected after adding new members, which setting is critical for managing traffic to the new member?

Correct Answer: D
When a pool is not working as expected immediately after adding new members to a busy environment, the
"Slow Ramp Time" setting is a critical factor
In a pool using the "Least Connections" load balancing method, a new member starts with zero active connections5858. Without a slow ramp time, the BIG-IP will immediately direct a high volume of new traffic to this server to "equalize" it with other members. This sudden surge can overwhelm the server's application stack before it has fully initialized or warmed its caches, leading to failures. By configuring a "Slow Ramp Time," the administrator ensures that the system gradually increases the amount of traffic sent to the new member over a specified duration. The traffic sent is proportional to the time the member has been available relative to the ramp time setting62. If the application fails only for users routed to new servers, reviewing this setting helps ensure that new capacity is integrated into the pool without disrupting service performance
insert code

Question 55

In an F5 BIG-IP system, a pool is configured with a health monitor and the "Manual Resume" feature is Enabled. If a pool member is marked Offline (Red) due to a health monitor failure, what will be the status of the member once the health monitor successfully passes again?

Correct Answer: A
The "Manual Resume" feature is a safety mechanism used when a pool is not working as expected due to flapping services or unstable backend applications. Normally, when a health monitor fails, the pool member is marked "Offline" (Red), and when the monitor passes, it automatically returns to "Available" (Green)47. However, if "Manual Resume" is enabled, the BIG-IP will not automatically put the member back into rotation after a failure48. Even if the health check begins to pass again, the member remains in an "Offline (Disabled)" state49. This requires an administrator to manually intervene and re-enable the member. This is a common point of confusion when troubleshooting; a member may show passing health checks but still not receive traffic because it is waiting for a manual administrative "resume" command. This feature is intended to prevent "unhealthy" servers from receiving traffic until an engineer has confirmed the root cause of the initial failure was resolved.
insert code
  • ««
  • «
  • …
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • »
[×]

Download PDF File

Enter your email address to download F5.F5CAB5.v2026-07-18.q66 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.