Free Access to VMware.2V0-41.23.v2024-12-31.q117 with Valid Practice Test (Page 8)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
VMware Certification
2V0-41.23 Exam
VMware.2V0-41.23.v2024-12-31.q117 Dumps

««
«
…
3
4
5
6
7
8
9
10
11
12
…
»
»»

Question 31

Which is an advantages of a L2 VPN In an NSX 4.x environment?

A.Use the same broadcast domain
B.Achieve better performance
C.Enables VM mobility with re-IP
D.Enables Multi-Cloud solutions

Correct Answer: A

Explanation
L2 VPN is a feature of NSX that allows extending Layer 2 networks across different sites or clouds over an IPsec tunnel. L2 VPN has an advantage of enabling VM mobility with re-IP, which means that VMs can be moved from one site to another without changing their IP addresses or network configurations. This is possible because L2 VPN allows both sites to use the same broadcast domain, which means that they share the same subnet and VLAN .

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 32

Which two CLI commands could be used to see if vmnic link status is down? (Choose two.)

A.esxcfg-nics -1
B.esxcfg-vmknic -1
C.esxcli network vswitch dvs vmware list
D.esxcfg-vmsvc/get.networks
E.esxcli network nic list

Correct Answer: A,E

The esxcli network nic list command lists all of the network interfaces on the ESXi host. The output of this command includes the link status of each interface.
The esxcfg-nics -1 command lists all of the network interfaces on the ESXi host in a single line.
The output of this command also includes the link status of each interface.
To see if the vmnic link status is down using the esxcli network nic list command, you can look at the Link column. If the Link status is Down, then the vmnic link is down.
To see if the vmnic link status is down using the esxcfg-nics -1 command, you can look at the Link Status column. If the Link Status is Down, then the vmnic link is down.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 33

An administrator has been tasked with Implementing the SSL certificates for the NSX Manager Cluster VIP. Which Is the correct way to implement this change?

A.
B.
C.
D.

Correct Answer: B

SSH as admin into the NSX manager with the cluster VIP and run nsxcli cluster certificate vip install certificate_id=<certificate_id> Send an API call to https://<nsx_mgr_vip>/api/2.0/services/trustmanagement/cluster_certificate/install?cluster_certificate_id=<certificate_id> These steps are consistent with the VMware NSX Documentation, which states that you need to install the SSL certificate for the cluster VIP on both the NSX Manager node and the cluster using the nsxcli command and the API call respectively.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 34

A customer has a network where BGP has been enabled and the BGP neighbor is configured on the Tier-0 Gateway. An NSX administrator used the get gateways command to retrieve this Information:

Which two commands must be executed to check BGP neighbor status? (Choose two.)

A.vrf 1
B.vrf 4
C.sa-nexedge-01(tier1_sr> get bgp neighbor
D.sa-nexedge-01(tier0_sr> get bgp neighbor
E.sa-nexedge-01(tier1_dr)> get bgp neighbor
F.vrf 3

Correct Answer: D,F

Explanation
BGP will be configured on the T0 SR. Connect to the VRF for the T0 SR and run get bgp neighbor once connected to it.
https://docs.vmware.com/en/VMware-Validated-Design/5.1/sddc-deployment-of-vmware-nsx-t-workload-domai For the BGP configuration on NSX-T, the Tier-0 Service Router (SR) is typically where BGP is configured.
To check the BGP neighbor status:
Connect to the VRF for the T0 SR, which is VRF 3 based on the provided output.
Run the command to get BGP neighbor status once connected to it.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 35

Which command on ESXI is used to verify the Local Control Plane connectivity with Central Control Plane?

A.
B.
C.
D.

Correct Answer: B

Explanation
According to the web search results, the command that is used to verify the Local Control Plane (LCP) connectivity with Central Control Plane (CCP) on ESXi is get control-cluster status. This command displays the status of the LCP and CCP components on the ESXi host, such as the LCP agent, CCP client, CCP server, and CCP connection. It also shows the IP address and port number of the CCP server that the LCP agent is connected to. If the LCP agent or CCP client are not running or not connected, it means that there is a problem with the LCP connectivity .

Comment: *

Name: *

Email: *

Verification: *

insert code

««
«
…
3
4
5
6
7
8
9
10
11
12
…
»
»»

[×]

Download PDF File

Enter your email address to download VMware.2V0-41.23.v2024-12-31.q117 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter