Free Access to VMware.2V0-41.23.v2024-12-31.q117 with Valid Practice Test (Page 9)

Request Exam Contact

Home
View All Exams
New QA's
Upload

PRACTICE EXAMS:

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce
Other

Oracle
Fortinet
IBM
Juniper
Microsoft
Cisco
Citrix
CompTIA
VMware
ISC
SAP
EMC
PMI
HP
Salesforce

Home
VMware Certification
2V0-41.23 Exam
VMware.2V0-41.23.v2024-12-31.q117 Dumps

««
«
…
4
5
6
7
8
9
10
11
12
13
…
»
»»

Question 36

An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events. Which message ID (msgld) should be used in the syslog export configuration command as a filler?

A.MONISTORING
B.SYSTEM
C.GROUPING
D.FABRIC

Correct Answer: D

Explanation
According to the VMware NSX Documentation2, the FABRIC message ID (msgld) captures messages related to NSX host preparation events, such as installation, upgrade, or uninstallation of NSX components on ESXi hosts. The syslog export configuration command for NSX host preparation events would look something like this:
set service syslog export FABRIC
The other options are either incorrect or not relevant for NSX host preparation events. MONITORING captures messages related to NSX monitoring features, such as alarms and system events2. SYSTEM captures messages related to NSX system events, such as login, logout, or configuration changes2. GROUPING captures messages related to NSX grouping objects, such as security groups, security tags, or IP sets2.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 37

Where is the insertion point for East-West network introspection?

A.Tier-0 router
B.Partner SVM
C.Guest VM vNIC
D.Host Physical NIC

Correct Answer: C

Explanation
The insertion point for East-West network introspection is the Guest VM vNIC. Network introspection is a service insertion feature that allows third-party network services to be integrated with NSX. Network introspection enables traffic redirection from the Guest VM vNIC to a service virtual machine (SVM) that runs the partner service. The SVM can then inspect, monitor, or modify the traffic before sending it back to the original destination1. The other options are incorrect because they are not the insertion points for East-West network introspection. The Tier-0 router is used for North-South routing and network services. The partner SVM is the service virtual machine that runs the partner service, not the insertion point. The host physical NIC is not involved in network introspection. References: Network Introspection Settings

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 38

What must be configured on Transport Nodes for encapsulation and decapsulation of Geneve protocol?

A.STT
B.TEP
C.UDP
D.VXLAN

Correct Answer: B

TEP stands for Tunnel End Point and is a logical interface that must be configured on transport nodes for encapsulation and decapsulation of Geneve protocol. Geneve is a tunneling protocol that encapsulates the original packet with an outer header that contains metadata such as the virtual network identifier (VNI) and the transport node IP address. TEPs are responsible for adding and removing the Geneve header as the packet traverses the overlay network.

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 39

Which is an advantages of a L2 VPN In an NSX 4.x environment?

A.Enables Multi-Cloud solutions
B.Achieve better performance
C.Enables VM mobility with re-IP
D.Use the same broadcast domain

Correct Answer: D

L2 VPN is a feature of NSX that allows extending Layer 2 networks across different sites or clouds over an IPsec tunnel. L2 VPN has an advantage of enabling VM mobility with re-IP, which means that VMs can be moved from one site to another without changing their IP addresses or network configurations. This is possible because L2 VPN allows both sites to use the same broadcast domain, which means that they share the same subnet and VLAN .

Comment: *

Name: *

Email: *

Verification: *

insert code

Question 40

An NSX administrator is creating a Tier-1 Gateway configured In Active-Standby High Availability Mode. In the event of node failure, the failover policy should not allow the original tailed node to become the Active node upon recovery.
Which failover policy meets this requirement?

A.Non-Preemptive
B.Preemptive
C.Enable Preemptive
D.Disable Preemptive

Correct Answer: A

According to the VMware NSX Documentation, a non-preemptive failover policy means that the original failed node will not become the active node upon recovery, unless the current active node fails again. This policy can help avoid unnecessary failovers and ensure stability.
The other options are either incorrect or not available for this configuration. Preemptive is the opposite of non-preemptive, meaning that the original failed node will become the active node upon recovery, if it has a higher priority than the current active node. Enable Preemptive and Disable Preemptive are not valid options for the failover policy, as the failover policy is a drop-down menu that only has two choices: Preemptive and Non-Preemptive.

Comment: *

Name: *

Email: *

Verification: *

insert code

««
«
…
4
5
6
7
8
9
10
11
12
13
…
»
»»

[×]

Download PDF File

Enter your email address to download VMware.2V0-41.23.v2024-12-31.q117 Dumps

Email:

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

DMCA
About
Contact Us
Privacy Policy
Terms & Conditions

©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.

Web Analytics Made Easy - Statcounter