FreeQAs
 Request Exam  Contact
  • Home
  • View All Exams
  • New QA's
  • Upload
PRACTICE EXAMS:
  • Oracle
  • Fortinet
  • Juniper
  • Microsoft
  • Cisco
  • Citrix
  • CompTIA
  • VMware
  • ISC
  • SAP
  • EMC
  • PMI
  • HP
  • Salesforce
  • Other
  • Oracle
    Oracle
  • Fortinet
    Fortinet
  • Juniper
    Juniper
  • Microsoft
    Microsoft
  • Cisco
    Cisco
  • Citrix
    Citrix
  • CompTIA
    CompTIA
  • VMware
    VMware
  • ISC
    ISC
  • SAP
    SAP
  • EMC
    EMC
  • PMI
    PMI
  • HP
    HP
  • Salesforce
    Salesforce
  1. Home
  2. HP Certification
  3. HPE7-A07 Exam
  4. HP.HPE7-A07.v2026-07-28.q58 Dumps
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
Download Now

Question 21

What is the recommended configuration to ensure link aggregation is consistent in a campus topology using VSX with two aggregation switches and downlinks to access switches?

Correct Answer: D
Comprehensive and Detailed Explanation From Exact Extract of HPE Aruba Networking Switching:
The VSX synchronization feature provides per-feature synchronization from the primary to the secondary VSX peer. For multi-chassis LAGs (MC-LAGs), the command that ensures both VSX peers maintain consistent LAG interface associations and attributes is entered under the VSX configuration context:
* Command syntax: vsx-sync mclag-interfaces
* Command context: config-vsx
Description (extract): Enables VSX synchronization of VSX LAG interface associations and attributes from the primary VSX switch to the secondary peer switch.
In a campus design with two aggregation switches in a VSX pair and access switches dual-homed using MC- LAG, enabling vsx-sync mclag-interfaces under the VSX context ensures consistent LAG membership, attributes, and behavior across the pair-avoiding configuration drift and aggregation inconsistencies.
References:* ArubaOS-CX VSX Command Reference; "vsx-sync mclag-interfaces" (syntax, command context, and description).* Aruba Campus Switching Best Practices with VSX; MC-LAG consistency and VSX feature synchronization guidelines.
insert code

Question 22

A deployment using AP-635S is connected to a stack of CX 6300s as shown.

The output of the snow LACP interfaces shews the following:

What is causing this issue?

Correct Answer: D
In an Aruba deployment, if an AP's interfaces show different LACP states, it often indicates a configuration mismatch. If one interface is up and the other is blocked as shown in the output, it's likely due to both interfaces on the AP being set to LACP active mode, which is a correct setting for establishing an LACP channel with Aruba switches like the CX 6300 series.
insert code

Question 23

Your customer added third-party USB dongles to the USB ports of their AOS 10 access points. The customer uses AP-615 and AP-635 Each AP is connected with a Cat 6A cable to a CX 6300F Class 4 PoE switch All APs are in the same group in HPE Aruba Networking Central and share the same configuration However, many of the dongles do not come up.
Which option will solve this issue?

Correct Answer: A
USB dongles often require additional power, which may exceed the power delivery capabilities of Class 4 PoE switches. Aruba AP-615 and AP-635 are designed to work with USB dongles that require additional power for proper operation. Since the Cat 6A cable can support higher power levels, replacing the Class 4 PoE switches with Class 6 PoE switches, which can deliver higher power, should resolve the issue with the dongles not powering up.
insert code

Question 24

A BGP routing tablecontains multiple routes to the same destination prefix.
Referring to the table below whichroutewould be marked with a ">" symbol?

Correct Answer: E
In BGP, the route marked with a ">" symbol is the best route that is chosen based on BGP attributes in the following order: highest weight (Cisco-specific), highest local preference, originated by BGP running on the local router, shortest AS path, lowest origin type, lowest MED, eBGP over iBGP, closest IGP neighbor, and lowest BGP router ID. Based on the table provided, Option E would be marked with a ">" symbol as it has the highest local preference of 100 which is a decisive factor in the BGP best path selection process.
insert code

Question 25

A customer's infrastructure is set up to use both primary and secondary gateway clusters on the SSID profile based on best practices What is a valid cause tor having an equal spirt in APs connected to the primary and secondary gateway clusters?

Correct Answer: C
In a high availability setup where both primary and secondary gateway clusters are present, APs are typically designed to connect to the primary cluster. If the APs are equally split between the primary and secondary, this may indicate that some APs cannot reach the primary cluster due to connectivity issues or reachability constraints, thus falling back to the secondary cluster.
insert code
  • «
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • …
  • »
  • »»
[×]

Download PDF File

Enter your email address to download HP.HPE7-A07.v2026-07-28.q58 Dumps

Email:

FreeQAs

Our website provides the Largest and the most Latest vendors Certification Exam materials around the world.

Using dumps we provide to Pass the Exam, we has the Valid Dumps with passing guranteed just which you need.

  • DMCA
  • About
  • Contact Us
  • Privacy Policy
  • Terms & Conditions
©2026 FreeQAs

www.freeqas.com materials do not contain actual questions and answers from Cisco's certification exams.